K223 / K224 / 2027
D.C. circuits overview

Full chapter

D.C. circuits

All 7 topics and the revision summary on one page.

01

Circuit symbols

Make a guess. You are not marked.

A circuit diagram shows a resistor symbol with an arrow drawn through it. What does the arrow mean?

  1. It shows that the resistor gives out light when it is on.
  2. It shows the direction in which the current flows.
  3. The resistance can be changed: it is a variable resistor.
Show the answer

The resistance can be changed: it is a variable resistor.

The arrow through the box is part of the symbol for a variable resistor. Turning a knob or sliding a contact changes its resistance.

In short

  • Use the standard symbols for cells, lamps, resistors, switches and meters.
  • On a cell symbol, the longer line is the positive terminal.
  • An arrow through a resistor means that its resistance can be changed.

A circuit diagram uses standard symbols to show each component and how the parts are joined.

Current is the charge passing a point each second, in amperes. P.d. is the energy transferred per coulomb between two points, in volts.

Draw the connecting wires as straight lines. The symbols are agreed around the world. The International Electrotechnical Commission (IEC) publishes them in its standard IEC 60617.

Direct current (d.c.) flows in one direction. The circuits in this chapter use steady d.c.: the current does not change while you take a reading.

Know each symbol and what it does

Each card gives a symbol, its name and its job. The light arrows on an LED point out.

Cell

Cell circuit symbolGives energy to the charge. The longer line is positive.+-

Gives energy to the charge. The longer line is positive.

Battery

Battery circuit symbolTwo or more cells joined together.+-

Two or more cells joined together.

Switch

Switch circuit symbolOpens or closes the circuit. Shown open.

Opens or closes the circuit. Shown open.

Lamp

Lamp circuit symbolGives out light, and warms up as it does.

Gives out light, and warms up as it does.

LED

LED circuit symbolGives out light when current flows the right way. The bar marks the cathode, K.K

Gives out light when current flows the right way. The bar marks the cathode, K.

Fixed resistor

Fixed resistor circuit symbolAdds a fixed resistance to the circuit.

Adds a fixed resistance to the circuit.

Variable resistor

Variable resistor circuit symbolIts resistance can be changed. The arrow is not a current arrow.

Its resistance can be changed. The arrow is not a current arrow.

Fuse

Fuse circuit symbolA thin wire that melts and breaks the circuit if the current is too large.

A thin wire that melts and breaks the circuit if the current is too large.

Ammeter

Ammeter circuit symbolMeasures the current. Connect it in series.A

Measures the current. Connect it in series.

Voltmeter

Voltmeter circuit symbolMeasures the p.d. between two points. Connect it in parallel.V

Measures the p.d. between two points. Connect it in parallel.

Each card shows a symbol, its name and its job. The symbol tells you what the part is. The wires joined to its two ends tell you where it sits in the circuit.

For a cell, the longer line is the positive terminal and the shorter line is the negative terminal. A battery is two or more cells joined together. Mark + and - whenever the direction of the current matters.

A variable resistor has a resistance that you can change. The arrow through it is part of the symbol, not a current arrow. A switch opens or closes a path. A fuse is a thin wire that melts and breaks the circuit if the current is too large for too long.

An LED is a light-emitting diode. It lights when the current flows through it the right way: in at the triangle side and out at the bar. The small arrows pointing out show the light it gives out. A real LED needs a resistor in series to keep its current small enough.

An arrow on a symbol is not a current arrow. The arrow through a variable resistor means it can be adjusted. The arrows on an LED or an LDR show light. Draw current arrows beside the wires.

Check your understanding

Which of these is true of the circuit symbol for a cell?

  1. Either line can be positive; the symbol does not show it.
  2. The longer line is the positive terminal.
  3. The shorter line is the positive terminal.
Show the answer

The longer line is the positive terminal.

In the cell symbol, the longer line marks the positive terminal and the shorter line marks the negative terminal.

02

Series and parallel connections

Make a guess. You are not marked.

Two wires cross on a circuit diagram, with no dot where they cross. What does that mean?

  1. They are joined if the two wires carry the same current.
  2. They are not connected; the current in each stays on its own wire.
  3. They are joined, because every crossing on a diagram is a junction.
Show the answer

They are not connected; the current in each stays on its own wire.

A junction is shown by a dot. Wires that cross without a dot pass over each other, so no current flows from one to the other.

In short

  • A dot shows a junction, where wires join.
  • Parts in series are on one path, one after another.
  • Parts in parallel are joined to the same two points, at both ends.

Whether parts are in series or in parallel depends on what they are joined to, not on where they sit on the page.

A circuit diagram uses standard symbols joined by straight lines for the wires.

Junctions and crossing wires

A junction is a point where wires join. Draw it as a dot. Where two wires cross without joining, leave out the dot, or draw a small bridge in one of the wires. Do not add a dot just because two lines pass close together.

Wires joined with no part between them act as one connection point, called a node. There is no p.d. between any two points on it. A wire can bend or take a longer route on the page and still be the same node.

Series or parallel?

Series
The parts are on one path, one after another. The current does not split between them, so the same current passes through each part.
Parallel
The parts are joined to the same two nodes, at both ends. Sharing just one point is not enough.

Older Christmas light sets had their bulbs wired in series, on one path. In a parallel set, each bulb has its own path between the same two wires.

Follow the connections, not the positions

A dot shows where wires join. Both drawings show the same network of three resistors. A cell could be joined across A and C.

One drawing of the network

One drawing of the networkR1 joins A to B. R2 joins B to C along the upper path, and R3 joins the same B and C along the lower path. Upright wires at B and C join the upper and lower junctions. No plain wire joins B straight to C.ABCR1R2R3R1: A/B; R2 and R3: B/C

Move R3 around the outside

Move R3 around the outsideThe same network is drawn again. A joins the left end of R1, and R1 ends at B. R2 joins B to C. From B, a wire goes up to the right end of R3. The left end of R3 goes round the left and bottom edges to C. The outer path has R3 in it, so it is not a short circuit. No wires cross.ABCR1R2R3The connections have not changed
Both drawings keep R1 between A and B, and R2 and R3 each between B and C. So R2 and R3 are in parallel. R1 is in series with that whole parallel group, wherever the symbols sit on the page.

R1 carries the current going into the R2 and R3 group. That does not mean R1 has the same current as R2 or R3 on its own. The current splits at B.

Redraw without changing the circuit

To redraw a circuit, first write down the two end points of every part. Keep each part between the same two points as you move it. A plain wire added straight from B to C would change the circuit. The current would take that wire instead of going through R2 and R3.

Meters follow the same rule. An ammeter goes in series in the path you want to measure. A voltmeter joins the two ends of the part or group you want to measure.

Sharing one point does not make parts parallel. R1 and R2 both touch B, but R1 joins A to B and R2 joins B to C. Parallel parts share both of their end points.

Check your understanding

R1 connects A to B. R2 and R3 each connect B to C, with no plain wire directly joining B to C. Which of these descriptions remains correct when the drawing is rearranged?

  1. R2 and R3 are in parallel with each other, and R1 is in series with their combination.
  2. The three resistors are in series, because they appear one after another in the drawing.
  3. R1 and R2 are parallel because they both connect to B.
Show the answer

R2 and R3 are in parallel with each other, and R1 is in series with their combination.

R2 and R3 share both endpoints, B and C. R1 carries the current entering or leaving that whole parallel group. Moving symbols on the page does not change these connections.

03

Series circuits

Make a guess. You are not marked.

Two identical lamps are connected in series with a cell and both glow. One lamp is unscrewed from its holder. What happens to the other lamp?

  1. It glows the same as before.
  2. It goes out.
  3. It glows brighter.
Show the answer

It goes out.

A series circuit has one path. Removing a lamp breaks that path, so no current flows anywhere in the circuit and the other lamp goes out.

In short

  • In series, the current is the same everywhere.
  • The p.d.s across the parts add up to the supply p.d.
  • Total resistance = R1 + R2 + ...

Parts in series carry the same current. Their p.d.s add up to the p.d. across the whole path.

For each resistor, V = IR uses the p.d. across that resistor and the current through it. Here Vs is the p.d. across the whole circuit outside the cell.

Why the current is the same

In a steady circuit, charge does not pile up anywhere. So the same amount of charge passes every point each second. A resistor transfers energy. It does not use up some of the current before the next resistor.

I = I1 = I2 = ...There is one path, so the same current passes through every part in series.

Each coulomb transfers some energy in each part it passes through. The energy per coulomb for the whole path is the sum of the energy per coulomb in each part. So the p.d.s add up.

Vs = V1 + V2 + ...The same current does not mean the same p.d. A bigger resistance takes a bigger p.d.

Add the resistances

For two resistors with the same current, V1 = IR1 and V2 = IR2. Adding these gives Vs = I(R1 + R2). So the pair acts like one resistor of R1 + R2.

Rseries = R1 + R2 + ...Adding a resistor in series always increases the total resistance.

One path: the same current, and the p.d.s add

The resistances are fixed, the wires have no resistance and the cell is ideal. The arrows show the direction of the current, not its size.

One path: same current through both resistors

One path: same current through both resistorsAn ideal 6.0 V cell drives a current round one closed path: R1: 2 ohm between A and B, then R2: 4 ohm between B and C. The same 1.0 A passes through both. The p.d. across A and B is 2.0 V, and across B and C it is 4.0 V. The switch at the bottom is closed.+-6.0 VR1: 2 ohmR2: 4 ohm2.0 V4.0 VABCI = 1.0 ASwitch closed

The p.d.s 2.0 V and 4.0 V add up to 6.0 V. The current is 1.0 A everywhere in the single path.

Open the only path

Open the only pathThe switch at the bottom is open, so the only path is broken. The current is zero everywhere, and each resistor has 0 V across it. The ideal cell still has 6.0 V, so the gap in the open switch has 6.0 V across it.+-6.0 VR1: 2 ohmR2: 4 ohm0 V0 VCurrent = 0 AOpen switch: 6.0 V across the gap

No current does not mean no p.d. The only path is broken, but the cell still has 6.0 V.

The closed 6.0 V circuit has one path through 2.0 Ω and 4.0 Ω. The current is 1.0 A, and the p.d.s are 2.0 V and 4.0 V. In the second drawing the switch is open: there is no current, but the cell still has 6.0 V.

One current, two p.d.s

2.0 Ω and 4.0 Ω across 6.0 V

Take the resistances as fixed, the wires as having no resistance, and the cell's p.d. as steady at 6.0 V.

  1. Total resistance = 2.0 + 4.0 = 6.0 Ω.
  2. Current = 6.0/6.0 = 1.0 A, through both resistors.
  3. Across 2.0 Ω: V = 1.0 x 2.0 = 2.0 V.
  4. Across 4.0 Ω: V = 1.0 x 4.0 = 4.0 V.

The p.d.s add up to 6.0 V. Each coulomb transfers 2.0 J in the first resistor and 4.0 J in the second. The current through them has not dropped.

Try it step by step

Work it out in steps: Total resistance in ohm, then Current in A, then p.d. across the first resistor in V.

  1. Problem 1. A 3.0 ohm resistor and a 9.0 ohm resistor are connected in series across a 6.0 V supply. Find the current and the p.d. across the 3.0 ohm resistor.
  2. Problem 2. A 5.0 ohm resistor and a 15 ohm resistor are in series across a 10 V supply. Find the current and the p.d. across the 5.0 ohm resistor.
  3. Problem 3. An 8.0 ohm resistor and a 4.0 ohm resistor are in series across a 9.0 V supply. Find the current and the p.d. across the 8.0 ohm resistor.
Show the answer

Problem 1.

Total resistance in ohm: R = 3.0 + 9.0 = 12 ohm

Current in A: I = V / R = 6.0 / 12 = 0.50 A

p.d. across the first resistor in V: V = IR = 0.50 x 3.0 = 1.5 V (2 sf)

Problem 2.

Total resistance in ohm: R = 5.0 + 15 = 20 ohm

Current in A: I = 10 / 20 = 0.50 A

p.d. across the first resistor in V: V = 0.50 x 5.0 = 2.5 V (2 sf)

Problem 3.

Total resistance in ohm: R = 8.0 + 4.0 = 12 ohm

Current in A: I = 9.0 / 12 = 0.75 A

p.d. across the first resistor in V: V = 0.75 x 8.0 = 6.0 V (2 sf)

With the same supply p.d., a larger total resistance means a smaller current.

What an open switch changes

Opening the only path stops the current everywhere in the circuit. Each resistor then has V = IR = 0 across it. The cell still has its e.m.f., so the full 6.0 V appears across the gap in the switch.

This is why older Christmas light sets went completely dark when a single bulb failed. Their bulbs were in series, so one failed bulb broke the only path.

No current does not always mean no p.d. An open gap can have a p.d. across it, even though no current flows through it.

Check your understanding

Fixed 3.0 ohm and 6.0 ohm resistors are in series across an ideal 9.0 V source. What is the potential difference across the 6.0 ohm resistor?

  1. 4.5 V
  2. 6.0 V
  3. 9.0 V
Show the answer

6.0 V

Total resistance is 3.0 + 6.0 = 9.0 ohm, so the shared current is 9.0/9.0 = 1.0 A. The 6.0 ohm resistor has V = IR = 1.0 x 6.0 = 6.0 V; the other has 3.0 V.

04

Parallel circuits

Make a guess. You are not marked.

One lamp is connected across a cell. A second identical lamp is now connected in parallel with the first. What happens to the current drawn from the cell?

  1. It stays the same.
  2. It halves.
  3. It doubles.
Show the answer

It doubles.

Each lamp still has the full cell p.d. across it, so each draws the same current as before. The cell now supplies both currents, twice as much in total.

In short

  • In parallel, each branch has the same p.d.
  • The branch currents add up to the main current.
  • Adding a branch lowers the total resistance.

Parallel branches are joined to the same two points, so they have the same p.d. Their currents add up to the current going into the group.

Follow the connections, not the shape of the drawing. Branches are parallel only if each one starts and ends at the same two nodes.

V1 = V2 = ... = VgroupEach branch is across the same two points. If the group is straight across the supply, Vgroup = Vs.

The current splits at one junction and joins up again at the other. No charge is lost or gained at a junction. So the current going in equals the sum of the branch currents.

This rule is called Kirchhoff's current law. The German scientist Gustav Kirchhoff described it in 1845.

Itotal = I1 + I2 + ...With the same p.d., a smaller resistance carries a larger current. The current need not split equally.

Each branch joins the same two points

The cell keeps 6.0 V across both branches. Both branches carry a current. The arrow lengths do not show the size of the current.

The same two resistors, joined across the same two points

The same two resistors, joined across the same two pointsAn ideal 6.0 V cell is joined to A and C. A 2.0 ohm resistor and a 4.0 ohm resistor each join A to C, so each has 6.0 V across it. The upper branch carries 3.0 A and the lower branch 1.5 A, both from A towards C. The cell's current is 4.5 A. No plain wire joins A straight to C.+-6.0 VAC2.0 ohm4.0 ohm4.5 A3.0 A; 6.0 V1.5 A; 6.0 VThe current splits, then joins up again

The combined resistance is 4/3 ohm, about 1.33 ohm. In series, the same two resistors gave 6.0 ohm.

The 2.0 Ω and 4.0 Ω resistors are now joined in parallel across 6.0 V. Each branch has the full 6.0 V. Their currents are 3.0 A and 1.5 A, so 4.5 A flows in the main wire.

The same two resistors, joined differently

2.0 Ω and 4.0 Ω in parallel across 6.0 V

  • Current in 2.0 Ω = 6.0/2.0 = 3.0 A.
  • Current in 4.0 Ω = 6.0/4.0 = 1.5 A.
  • Total current = 3.0 + 1.5 = 4.5 A.

Both branches carry a current. The combined resistance is Vs/Itotal = 6.0/4.5 = 4/3 Ω, about 1.33 Ω.

Find the combined resistance

Each branch current is the shared p.d. divided by that branch's resistance. Adding them gives Itotal = V/R1 + V/R2 + ... . Since Itotal = V/Rparallel, dividing through by V gives the rule below.

1/Rparallel = 1/R1 + 1/R2 + ...Add the reciprocals, then take the reciprocal of the sum. The reciprocal of a number is 1 divided by it.

For exactly two resistors, this becomes Rparallel = R1R2/(R1 + R2). The reciprocal rule also works for three or more branches.

Three parallel branches

6 Ω, 12 Ω and 4 Ω

1/R = 1/6 + 1/12 + 1/4 = 2/12 + 1/12 + 3/12 = 6/12 = 1/2, so R = 2 Ω.

Across 6 V, the branch currents are 1.0 A, 0.50 A and 1.5 A. They add up to 3.0 A, which agrees with 6 V / 2 Ω.

Try it step by step

Work it out in steps: Current in the smaller resistor in A, then Current in the larger resistor in A, then Total current in A, then Combined resistance in ohm.

  1. Problem 1. A 3.0 ohm resistor and a 6.0 ohm resistor are connected in parallel across a 6.0 V supply. Find the total current and the combined resistance.
  2. Problem 2. A 4.0 ohm resistor and a 12 ohm resistor are in parallel across a 12 V supply. Find the total current and the combined resistance.
  3. Problem 3. A 5.0 ohm resistor and a 20 ohm resistor are in parallel across a 10 V supply. Find the total current and the combined resistance.
Show the answer

Problem 1.

Current in the smaller resistor in A: I1 = 6.0 / 3.0 = 2.0 A

Current in the larger resistor in A: I2 = 6.0 / 6.0 = 1.0 A

Total current in A: I = 2.0 + 1.0 = 3.0 A

Combined resistance in ohm: R = V / I = 6.0 / 3.0 = 2.0 ohm (check: 1/3 + 1/6 = 1/2)

Problem 2.

Current in the smaller resistor in A: I1 = 12 / 4.0 = 3.0 A

Current in the larger resistor in A: I2 = 12 / 12 = 1.0 A

Total current in A: I = 3.0 + 1.0 = 4.0 A

Combined resistance in ohm: R = 12 / 4.0 = 3.0 ohm (2 sf)

Problem 3.

Current in the smaller resistor in A: I1 = 10 / 5.0 = 2.0 A

Current in the larger resistor in A: I2 = 10 / 20 = 0.50 A

Total current in A: I = 2.0 + 0.50 = 2.5 A

Combined resistance in ohm: R = 10 / 2.5 = 4.0 ohm (2 sf)

The combined resistance is always smaller than the smallest branch. An extra branch gives the current another path, so more current flows for the same p.d. When a branch is opened shows what happens the other way round.

Take the reciprocal at the end. If 1/R = 1/2, then R = 2 Ω, not 0.5 Ω. Check that your answer is smaller than the smallest branch.

Check your understanding

Fixed 3.0 ohm and 6.0 ohm resistors are connected directly in parallel across an ideal 6.0 V source. What current does the source supply?

  1. 3.0 A
  2. 0.667 A
  3. 2.0 A
Show the answer

3.0 A

Each branch has 6.0 V. Their currents are 6.0/3.0 = 2.0 A and 6.0/6.0 = 1.0 A, so the source supplies 2.0 + 1.0 = 3.0 A.

05

Solving a complete circuit

In short

  • Replace a parallel group by its combined resistance, then add the series resistances.
  • Supply current = supply p.d. / total resistance.
  • Work back: find the p.d. across each part, then the current in each branch.

To solve a circuit with series and parallel parts, replace each group by one resistance and find the supply current. Then work back to each part.

Series parts share one current. Parallel branches share one p.d. R = V/I must use the p.d. and current of the same part, or of the same whole group.

Keep the same end points

One resistance can replace a group if it gives the same current for the same p.d. across the group's two ends. This is the group's equivalent resistance. Inside the group, each part still has its own current and p.d., so you work back to find them.

The supply in this example is 12.0 V, the p.d. of a typical car battery. Car batteries are lead-acid batteries, a type first made by the French physicist Gaston Planté in 1859.

Replace a group, but keep its two end points

R1 is between A and B. The two parallel branches are between B and C. Keep these labels when you replace a group and when you work back.

Start with the complete network

Start with the complete networkAn ideal 12.0 V cell is joined across A and C. R1 is 4.0 ohm between A and B. R2 is 6.0 ohm between B and C, and R3 is 12.0 ohm between the same B and C. R1 carries the cell's current, 1.50 A. R2 carries 1.0 A and R3 carries 0.50 A. The A to B part and the B to C part each have 6.0 V across them.+-12.0 VABCR1: 4.0 ohmR2: 6.0 ohmR3: 12.0 ohm1.50 A1.0 A0.50 AV_AB = 6.0 V; V_BC = 6.0 V

First replace only the parallel group between B and C. Its branches do not get the full 12.0 V.

Replace the B to C group by 4.0 ohm

Replace the B to C group by 4.0 ohmThe 6.0 ohm and 12.0 ohm parallel branches between B and C are replaced by one 4.0 ohm resistor that acts the same. R1 is still 4.0 ohm between A and B, and the cell is still across A and C. The two parts are in series, 8.0 ohm in total, so the cell's current is 1.50 A at 12.0 V.+-12.0 VR1: 4 ohmB/C: 4 ohm6.0 V6.0 VABCI = 1.50 ASwitch closed

The p.d.s 6.0 V and 6.0 V add up to 12.0 V. The current is 1.50 A everywhere in the single path.

Replace the whole network by 8.0 ohm

Replace the whole network by 8.0 ohmThe whole network is replaced by one 8.0 ohm resistor between A and C, across the same ideal 12.0 V cell. The cell's current is 1.50 A. Point B is inside the group, so it no longer appears. This single resistor does not show the p.d. across each part.+-12.0 VAC8.0 ohm1.50 A

Now work back: from the cell's current to the p.d. across each part, then to the current in each branch.

R1 = 4.0 Ω joins A to B. The 6.0 Ω and 12.0 Ω branches each join B to C. Replace only the B to C group first, then the whole circuit.

Replace, then work back

12.0 V across 4.0 Ω plus a parallel group

Take the supply as ideal, the wires as having no resistance and the resistances as fixed.

  1. Replace the B to C group: 6.0 Ω and 12.0 Ω in parallel give (6.0 x 12.0)/(6.0 + 12.0) = 4.0 Ω.
  2. Find the total resistance: 4.0 + 4.0 = 8.0 Ω from A to C.
  3. Find the supply current: 12.0/8.0 = 1.50 A. This is also the current through R1.
  4. Find the p.d. across each part: VAB = 1.50 x 4.0 = 6.0 V. So VBC = 12.0 - 6.0 = 6.0 V.
  5. Find the branch currents: 6.0/6.0 = 1.0 A through the 6.0 Ω resistor, and 6.0/12.0 = 0.50 A through the 12.0 Ω resistor.

Check: 1.0 + 0.50 = 1.50 A at B, and 6.0 + 6.0 = 12.0 V along either path from A to C.

Try it step by step

Work it out in steps: Parallel group resistance in ohm, then Total resistance in ohm, then Source current in A, then p.d. across the series resistor in V.

  1. Problem 1. A 2.0 ohm resistor is in series with a parallel pair of 3.0 ohm and 6.0 ohm resistors. The supply is 8.0 V. Find the source current and the p.d. across the 2.0 ohm resistor.
  2. Problem 2. A 3.0 ohm resistor is in series with a parallel pair of 4.0 ohm and 12 ohm resistors. The supply is 9.0 V. Find the source current and the p.d. across the 3.0 ohm resistor.
  3. Problem 3. A 6.0 ohm resistor is in series with a parallel pair of two 10 ohm resistors. The supply is 11 V. Find the source current and the p.d. across the 6.0 ohm resistor.
Show the answer

Problem 1.

Parallel group resistance in ohm: Group: 1/R = 1/3.0 + 1/6.0 = 1/2.0, so R = 2.0 ohm

Total resistance in ohm: Total = 2.0 + 2.0 = 4.0 ohm

Source current in A: I = 8.0 / 4.0 = 2.0 A

p.d. across the series resistor in V: V = IR = 2.0 x 2.0 = 4.0 V (the group takes the other 4.0 V)

Problem 2.

Parallel group resistance in ohm: Group: (4.0 x 12) / (4.0 + 12) = 3.0 ohm

Total resistance in ohm: Total = 3.0 + 3.0 = 6.0 ohm

Source current in A: I = 9.0 / 6.0 = 1.5 A

p.d. across the series resistor in V: V = 1.5 x 3.0 = 4.5 V (2 sf)

Problem 3.

Parallel group resistance in ohm: Group: two equal 10 ohm resistors in parallel give 5.0 ohm

Total resistance in ohm: Total = 6.0 + 5.0 = 11 ohm

Source current in A: I = 11 / 11 = 1.0 A

p.d. across the series resistor in V: V = 1.0 x 6.0 = 6.0 V (2 sf)

Dividing the group's 6.0 V by the total current, 1.50 A, gives the group's 4.0 Ω. It is not the resistance of either branch.

Always finish with two checks. The branch currents must add up to the current into the junction. The p.d.s along any path from A to C must add up to the supply p.d.

Do not put the full supply p.d. across a parallel group. Some of it is across the resistor in series with the group. Find the p.d. across the group first.

Check your understanding

A 4.0 ohm resistor is in series with two 8.0 ohm resistors in parallel, across an ideal 12 V supply. What is the p.d. across one of the 8.0 ohm resistors?

  1. 6.0 V
  2. 12 V
  3. 3.0 V
Show the answer

6.0 V

Two 8.0 ohm resistors in parallel act as 4.0 ohm, so the total is 8.0 ohm and the current is 12/8.0 = 1.5 A. The 4.0 ohm resistor takes 1.5 x 4.0 = 6.0 V, which leaves 6.0 V across the pair. Each branch has that same 6.0 V.

06

When a branch is opened

Make a guess. You are not marked.

Two identical lamps are in parallel, directly across a cell whose p.d. stays fixed. The filament of one lamp breaks. What happens to the other lamp?

  1. It stays just as bright, because its p.d. has not changed.
  2. It goes out, because the circuit is now broken.
  3. It gets brighter, because it now gets the current that went to the broken lamp.
Show the answer

It stays just as bright, because its p.d. has not changed.

Each lamp is directly across the cell, so each has the full cell p.d. Breaking one branch does not change the other branch's p.d. or current.

In short

  • Branches joined straight across a fixed supply keep their p.d. and current when another branch opens.
  • Opening a branch raises the total resistance, so the supply current falls.
  • With a resistor in series with the branches, work out the new p.d.s again.

When a branch is opened, first work out the new total resistance and supply current. Then find what happens to the p.d. across each part.

A parallel group has less resistance than any one of its branches. In a complete circuit, you work back from the supply current.

Branches straight across the supply

Suppose the branches are joined straight across a supply whose p.d. stays fixed. Opening one branch leaves the same p.d. across the others, so their currents do not change. The supply current falls, because the open branch no longer carries any current.

Mains wiring in a home works this way. In Singapore, the mains supply is 230 V. The lamps and sockets are joined in parallel across it, so switching one off does not change the others. Practical electricity shows how they are switched safely.

A branch current can rise while the total current falls

Now go back to the complete circuit: 4.0 Ω in series with 6.0 Ω and 12.0 Ω in parallel, across 12.0 V. There, the supply current was 1.50 A and the 6.0 Ω branch carried 1.0 A.

Open one branch and work it out again

The 12.0 V cell and R1 = 4.0 ohm are unchanged. Only the 12.0 ohm branch between B and C is opened.

Open only the 12 ohm branch

Open only the 12 ohm branchThe 12.0 V cell still drives a current through R1, 4.0 ohm, between A and B. The 6.0 ohm branch between B and C is still connected. Only the 12.0 ohm branch has an open switch. The cell's current is now 1.20 A, and it all passes through the 6.0 ohm branch. The open branch has no current. V_AB is 4.8 V and V_BC is 7.2 V.+-12.0 VABCR1: 4.0 ohmR2: 6.0 ohmR3: 12.0 ohm1.20 A1.20 A0 AV_AB = 4.8 V; V_BC = 7.2 V

The total current falls, but the current in the 6.0 ohm branch rises. R1 now takes a smaller p.d., which leaves more for the branch.

Only the 12.0 Ω branch is opened. The path through 4.0 Ω and 6.0 Ω stays closed.

Open only the 12.0 Ω branch. The path left is 4.0 Ω in series with 6.0 Ω, so the total resistance is 10.0 Ω. The supply current is 12.0/10.0 = 1.20 A, and all of it passes through the 6.0 Ω resistor.

So the 6.0 Ω branch current rises from 1.0 A to 1.20 A, even though the supply current falls from 1.50 A to 1.20 A. R1 now takes a smaller p.d., 1.20 x 4.0 = 4.8 V. That leaves 7.2 V across the 6.0 Ω resistor, more than the 6.0 V before.

Work it out again; do not guess. The other branches stay the same only when they are straight across a fixed supply. With a resistor in series, the p.d. across the branches changes.

Check your understanding

An ideal 12.0 V source supplies a 4.0 ohm resistor in series with parallel 6.0 ohm and 12.0 ohm branches. Initially the source current is 1.50 A and the 6.0 ohm branch current is 1.0 A. Only the 12.0 ohm branch is then opened. What happens?

  1. Source current falls to 1.20 A, while the 6.0 ohm branch current rises to 1.20 A.
  2. Every current becomes zero, because opening one branch breaks the circuit.
  3. The source current becomes 1.0 A and the 6.0 ohm branch current is unchanged.
Show the answer

Source current falls to 1.20 A, while the 6.0 ohm branch current rises to 1.20 A.

The remaining path has 4.0 + 6.0 = 10.0 ohm, so its current is 12.0/10.0 = 1.20 A everywhere. The 4.0 ohm drop falls to 4.8 V, leaving 7.2 V across the 6.0 ohm resistor. Total current falls even though this branch current rises.

07

Testing the circuit rules

Make a guess. You are not marked.

Two lamps are in parallel across a cell. You want to measure the total current from the cell. Where should the ammeter go?

  1. Across the terminals of the cell, in parallel with it.
  2. In one of the two branches, right next to one of the lamps.
  3. In the main wire, before the current splits between the lamps.
Show the answer

In the main wire, before the current splits between the lamps.

The total current flows in the main wire, between the cell and the first junction. An ammeter there, in series, reads it.

In short

  • Put an ammeter in the main wire for the total current, or in one branch for that branch's current.
  • Put the voltmeter across exactly the part or group you are testing.
  • Readings should agree with the rules, apart from small meter errors.

You can test the series and parallel rules by measuring currents and p.d.s. Each reading must come from the right place in the circuit.

An ammeter goes in series in the path you measure. A voltmeter goes across the two ends of the part you measure.

Use a low-voltage cell or battery, a switch and suitable resistors. Disconnect the supply while you change the connections. Choose resistors that do not heat up much, so that their resistance stays the same.

A digital multimeter can measure current, p.d. or resistance. Set it to the right quantity and range before each reading.

Pair each p.d. reading with the right current reading

These are the readings the rules predict, not real results. The meters are ideal: the ammeter has almost no resistance and the voltmeter takes almost no current.

Measure the whole series circuit

Measure the whole series circuitAn ammeter sits in the main wire from the cell's + terminal, before point A. A 10.0 ohm resistor joins A to B and a 20.0 ohm resistor joins B to C. A voltmeter is joined across A and C, across both resistors. With ideal meters it reads 3.00 V, and the ammeter reads 0.100 A. The p.d.s across the two resistors are 1.00 V and 2.00 V. A closed switch is in the return wire.+-3.00 VA0.100 A+-B10.0 ohm20.0 ohm1.00 V2.00 VVAC+-3.00 VSwitch closed

Resistance of the whole circuit: 3.00/0.100 = 30.0 ohm. The voltmeter is across both resistors, so its 3.00 V is not the p.d. across either one.

Measure the whole parallel circuit

Measure the whole parallel circuitAn ammeter sits in the main wire from the cell's + terminal, before point A. A 10.0 ohm resistor and a 20.0 ohm resistor are in separate branches from A to C. A voltmeter is joined across A and C. With ideal meters and 3.00 V across A and C, the branch currents are 0.300 A and 0.150 A, and the main ammeter reads 0.450 A. A closed switch is in the return wire.+-3.00 VA0.450 A+-10.0 ohm20.0 ohm0.300 A0.150 AVAC+-3.00 VSwitch closed

Resistance of the whole circuit: 3.00/0.450 = 6.67 ohm. The main ammeter reads the two branch currents added together.

Both circuits use 10.0 Ω and 20.0 Ω resistors with 3.00 V across them. The main ammeter reads the total current. The voltmeter across A and C reads the p.d. across the whole network.

For 3.00 V across each network, the rules predict these readings:

  • Series: the total current is 0.100 A. The 10.0 Ω resistor has 1.00 V across it and the 20.0 Ω resistor has 2.00 V. The whole circuit's resistance is 3.00/0.100 = 30.0 Ω.
  • Parallel: the currents are 0.300 A through 10.0 Ω and 0.150 A through 20.0 Ω. The total current is 0.450 A, so the whole circuit's resistance is 3.00/0.450 = 6.67 Ω.
More detail (optional)
  1. Choose the reading. For the total current, put the ammeter in the main wire. For one branch, put it in that branch. Put the voltmeter across the exact part or group you are testing.
  2. Set the range and the + terminal. Use a d.c. range bigger than the reading you expect. A battery labelled 3 V can give a little more than 3 V. Join each meter's + terminal to the side nearer the cell's + terminal.
  3. Record where each reading was taken. Name the part or the two points, and give units. Compare the main current with the sum of the branch currents, or the supply p.d. with the sum of the series p.d.s.
  4. Find a resistance from a matching pair. For one part, divide its p.d. by its current. For the whole circuit, divide the p.d. across A and C by the total current.

If you move one meter from place to place, the readings are taken at different times. The battery's p.d. can drift and the resistors can warm up in between. Check the supply, and let the readings settle.

Loose contacts add resistance. A meter can only show so many digits. Repeat readings to see how much they scatter. But fix a wrong connection or range straight away: repeating a mistake does not make it right.

Real readings will not match the rules exactly. For example, a total current of 0.448 A against 0.450 A still supports the parallel rule. The small difference comes from the meters and the contacts.

Brightness is not a current reading. A lamp's resistance changes as its filament heats up. Use an ammeter, and use fixed resistors when you test the rules.

Check your understanding

Two resistors are in series with a battery. A voltmeter reads 1.02 V across one resistor and 1.96 V across the other. Across the battery it reads 3.00 V. Which of these is the best conclusion?

  1. The rule is wrong, because the two p.d.s do not add to exactly 3.00 V.
  2. The readings support the rule, since 2.98 V is close to 3.00 V.
  3. A meter is faulty, because resistors in series should have equal p.d.s.
Show the answer

The readings support the rule, since 2.98 V is close to 3.00 V.

1.02 + 1.96 = 2.98 V. A difference of 0.02 V is small enough to come from the meter and the contacts, so the readings fit the rule that series p.d.s add up.

Revision summary

Symbols and connections

Use the standard symbols and follow each part's two end points. A dot marks a junction. Series parts share one path and one current. Parallel branches share both end points and so have the same p.d. A redrawn circuit is the same circuit only if every connection is unchanged.

Series
I = I1 = I2 = ...; Vs = V1 + V2 + ...; Rseries = R1 + R2 + ... . The same current does not mean the same p.d.
Parallel
V1 = V2 = ... = Vgroup; Itotal = I1 + I2 + ...; 1/Rparallel = 1/R1 + 1/R2 + ... . Take the reciprocal after adding. For two resistors, Rparallel = R1R2/(R1 + R2).
One part or one group
V = IR, using its own p.d. and current. In these examples the wires have no resistance and the supply is ideal. Vs is the p.d. across the whole circuit outside the supply.

Solve, change and test a circuit

  1. Find the nodes and a series or parallel group.
  2. Replace the group by its equivalent resistance, keeping its two end points.
  3. Find the total resistance and the supply current.
  4. Work back to the p.d. across each group and the current in each branch.
  5. Check that currents add up at each junction and that p.d.s add up along each path.

Opening a branch that is straight across a fixed supply leaves the other branches unchanged. Opening a branch inside a larger circuit can change the p.d. across the branch that is left. Work the circuit out again before you predict.

An ammeter goes in series in the path you measure; a voltmeter goes across the two points you measure. The whole circuit's resistance needs the whole p.d. and the total current. Record readings with units and say where each was taken. 1 mA = 0.001 A; 1 mV = 0.001 V; 1 kΩ = 1000 Ω.

Back to circuit symbols

Practise exam questions

Write your answer first, then tick the mark points it makes.

Exam-style question

Two resistors are connected in parallel to a cell. State how the currents in the resistors are related to the current from the cell, and how the potential differences across them compare. [2]

Saved on this browser only. Anyone using this browser can see it.

Exam-style question

A 12 V battery of negligible internal resistance is connected to a 2.0 Ω resistor in series with a parallel pair of resistors of 6.0 Ω and 3.0 Ω. Calculate the current from the battery and the current in the 6.0 Ω resistor. [4]

Saved on this browser only. Anyone using this browser can see it.

Exam-style question

A 4.0 Ω resistor and an 8.0 Ω resistor are connected in series to a 6.0 V battery of negligible internal resistance. Calculate the current in the circuit and the potential difference across the 8.0 Ω resistor. [3]

Saved on this browser only. Anyone using this browser can see it.

Quick recall

Card 1 of 7. Answer in your head, then check.

Which of these is true of the circuit symbol for a cell? (A) Either line can be positive; the symbol does not show it. (B) The longer line is the positive terminal. (C) The shorter line is the positive terminal.