K223 / K224 / 2027
Electric charge and current of electricity overview

Lesson 5 of 6

Resistance

  • I can state resistance as potential difference divided by current.Syllabus

    Syllabus K223 / K224, 10(h). State resistance as potential difference divided by current.

  • I can apply R = V/I to new situations and problems.Syllabus

    Syllabus K223 / K224, 10(i). Apply R = V/I to new situations and problems.

Make a guess. You are not marked.

Two resistors each have 6.0 V across them. Resistor A carries 0.50 A and resistor B carries 0.20 A. Which has the greater resistance?

  1. They are equal, because both resistors have the same p.d. across them.
  2. B, because it lets less current through at the same p.d.
  3. A, because it carries the larger current.
Show the answer

B, because it lets less current through at the same p.d.

R = V/I. For A, 6.0/0.50 = 12 ohm. For B, 6.0/0.20 = 30 ohm. Less current at the same p.d. means more resistance.

In short

  • Resistance R = V/I, measured in ohms, Ω.
  • Use the p.d. across a component and the current through that same component.
  • At the same p.d., more resistance means less current.

The resistance of a component is the p.d. across it divided by the current through it: R = V/I.

Measure the current I through the component with an ammeter, in amperes. Measure the p.d. V across it with a voltmeter, in volts. Use readings taken at the same time.

R = V/IResistance = p.d. / current. Rearranged: V = IR and I = V/R. The unit is the ohm, Ω. 1 Ω = 1 V/A.

Resistance tells you how hard it is to drive a current through a component. With the same p.d. across them, a component with more resistance lets less current through.

The ohm is named after the German scientist Georg Ohm. In 1827 he published measurements of voltage and current in simple circuits made with different lengths of wire.

A value of V/I is the resistance for that one reading. If the component heats up, its resistance can change. Then a new p.d. may give a different value of V/I.

Use paired readings

Find the resistance, then the new current

The p.d. across a resistor is 6.0 V and the current through it is 0.20 A.

R = V/I = 6.0/0.20 = 30 Ω.

The p.d. is raised to 9.0 V. If the resistance stays at 30 Ω, the new current is I = V/R = 9.0/30 = 0.30 A.

This assumes that the resistor does not heat up. If it did, its resistance could change and the current would be different.

Try it step by step

Work it out in steps: Resistance R = V / I in ohm, then Current at the new p.d. in A.

  1. Problem 1. The p.d. across a resistor is 4.0 V when the current through it is 0.25 A. Find its resistance, then the current when the p.d. is raised to 6.0 V, assuming the resistance stays the same.
  2. Problem 2. The p.d. across a resistor is 9.0 V when the current is 0.30 A. Find its resistance, then the current at 12 V, assuming the resistance stays the same.
  3. Problem 3. The p.d. across a resistor is 7.5 V when the current is 0.50 A. Find its resistance, then the current at 3.0 V, assuming the resistance stays the same.
Show the answer

Problem 1.

Resistance R = V / I in ohm: R = 4.0 / 0.25 = 16 ohm

Current at the new p.d. in A: I = V / R = 6.0 / 16 = 0.375 A, which is 0.38 A to 2 sf

Problem 2.

Resistance R = V / I in ohm: R = 9.0 / 0.30 = 30 ohm

Current at the new p.d. in A: I = 12 / 30 = 0.40 A (2 sf)

Problem 3.

Resistance R = V / I in ohm: R = 7.5 / 0.50 = 15 ohm

Current at the new p.d. in A: I = 3.0 / 15 = 0.20 A (2 sf)

Measure a resistance

Use a low-voltage supply. Put an ammeter in series with the component and a voltmeter across it. Wait for the readings to settle, then record both together. Work out R = V/I.

Divide V by I, not I by V. For a resistor with 0.25 A at 6.0 V, 0.25/6.0 gives 0.042, far too small. Write R = V/I before you put in the numbers. Use the p.d. and the current of the same component.

Check your understanding

A voltmeter reads 6.0 V across a resistor while an ammeter measures 0.20 A through that resistor. What is its resistance at this operating point?

  1. 30 ohm
  2. 0.033 ohm
  3. 1.2 ohm
Show the answer

30 ohm

R = V/I = 6.0 / 0.20 = 30 ohm. The two readings refer to the same resistor. This result alone does not show that its resistance stays constant at other operating points.