K223 / K224 / 2027
Electric charge and current of electricity overview

Lesson 4 of 6

Ammeters and voltmeters

  • I can define current as charge flow per second, measured in amperes.Syllabus

    Syllabus K223 / K224, 10(c). Define current as charge flow per second, measured in amperes.

  • I can define potential difference across a component as work per charge through it, measured in volts.Syllabus

    Syllabus K223 / K224, 10(g). Define potential difference across a component as work per charge through it, measured in volts.

Make a guess. You are not marked.

By mistake, a student connects a voltmeter in series with a lamp and a cell. The voltmeter has a very high resistance. What happens?

  1. A very large current flows and damages the voltmeter.
  2. The lamp stays off, because almost no current can flow through it.
  3. The lamp glows normally, and the voltmeter reads the p.d. across the lamp.
Show the answer

The lamp stays off, because almost no current can flow through it.

The voltmeter's very high resistance is now in the only path, so the current is tiny. The lamp needs a much larger current to glow.

In short

  • An ammeter measures current. Connect it in series with the component.
  • A voltmeter measures p.d. Connect it in parallel, across the component.
  • Pick a range bigger than the reading you expect.

An ammeter goes in series to measure the current through a component. A voltmeter goes in parallel, across the component, to measure the p.d.

Current is the charge passing a point each second. P.d. is the energy transferred per coulomb between two points.

An ammeter goes in series

An ammeter is drawn as a circle with an A inside. To measure the current through a lamp, break the circuit next to the lamp and put the ammeter in the gap. Now all of the lamp's current passes through the meter. This is a series connection: the parts are joined one after another, in one path.

An ammeter has a very low resistance, so it hardly changes the current it measures. Never connect it straight across a cell or a lamp. It would give the current an easy path round them, and a very large current could flow.

A voltmeter goes in parallel

A voltmeter is drawn as a circle with a V inside. Connect one lead to each end of the component. This is a parallel connection: the meter sits across the component, beside the main path.

A voltmeter has a very high resistance, so it takes almost no current. That is why it must not go in series. There, it would let almost no current through, and the lamp would stay off.

Measure current through and p.d. across the same resistor

A is an ammeter in series. V is a voltmeter joined to the two ends of the resistor. The + signs show which way round to connect each meter.

An ammeter in series and a voltmeter in parallel measure the resistorThe cell is on the left, with its positive line above its negative line. The top wire runs through ammeter A and then a resistor, and returns to the cell along the right and bottom wires. The ammeter's left terminal is positive. Two wires go down from the two ends of the resistor to voltmeter V, whose left terminal is positive. The ammeter reads 0.20 ampere and the voltmeter reads 6.0 volts. No wire goes round the resistor or either meter.+-SourceA+-0.20 AMeasured resistorV+-6.0 VBoth readings concern this resistor

Readings: 0.20 A through the resistor and 6.0 V across it.

We treat both meters as ideal. The voltmeter takes almost no current, and the ammeter has almost no p.d. across it. So the ammeter reads the current in the resistor.

The ammeter is in series with the resistor. The voltmeter is joined to the two ends of the resistor. Each meter's + terminal is on the side nearer the cell's + terminal.

Get the connections and the range right

For d.c., join each meter's + terminal to the side nearer the cell's + terminal. On a meter with a needle, a needle that tries to go below zero means the leads are swapped.

Pick a range bigger than the reading you expect. A 0-5 V range cannot show 6.0 V. If you are unsure, start on the largest range. Then switch down to the smallest range that still fits, for a more exact reading.

Read a needle scale with your eye straight in front of the needle. This avoids parallax error, a wrong reading caused by looking at the scale from an angle.

Early current meters used an effect found by Hans Christian Oersted in 1820. A current in a wire makes a nearby compass needle turn. Today one digital multimeter can be set to work as an ammeter or a voltmeter.

Do not swap the meters. A voltmeter in series stops the current. An ammeter across a component lets a large current flow round it.

Check your understanding

Which of these connections measures the current through a lamp and the p.d. across it?

  1. Both meters in series with the lamp, one on each side of it.
  2. An ammeter in series with the lamp, and a voltmeter joined across the two ends of the lamp.
  3. An ammeter joined across the two ends of the lamp, and a voltmeter in series with the lamp.
Show the answer

An ammeter in series with the lamp, and a voltmeter joined across the two ends of the lamp.

The lamp's current must pass through the ammeter, so it goes in series. The p.d. is measured between the lamp's two ends, so the voltmeter goes in parallel with the lamp.