K223 / K224 / 2027
D.C. circuits overview

Lesson 3 of 7

Series circuits

  • I can state and apply the equal-current rule for a series circuit.Syllabus

    Syllabus K223 / K224, 11(b). State and apply the equal-current rule for a series circuit.

  • I can state and apply the sum of series potential differences.Syllabus

    Syllabus K223 / K224, 11(c). State and apply the sum of series potential differences.

  • I can recall and apply effective resistance for a number of resistors in series and in parallel.Syllabus

    Syllabus K223 / K224, 11(f). Recall and apply effective resistance for a number of resistors in series and in parallel.

Make a guess. You are not marked.

Two identical lamps are connected in series with a cell and both glow. One lamp is unscrewed from its holder. What happens to the other lamp?

  1. It glows the same as before.
  2. It goes out.
  3. It glows brighter.
Show the answer

It goes out.

A series circuit has one path. Removing a lamp breaks that path, so no current flows anywhere in the circuit and the other lamp goes out.

In short

  • In series, the current is the same everywhere.
  • The p.d.s across the parts add up to the supply p.d.
  • Total resistance = R1 + R2 + ...

Parts in series carry the same current. Their p.d.s add up to the p.d. across the whole path.

For each resistor, V = IR uses the p.d. across that resistor and the current through it. Here Vs is the p.d. across the whole circuit outside the cell.

Why the current is the same

In a steady circuit, charge does not pile up anywhere. So the same amount of charge passes every point each second. A resistor transfers energy. It does not use up some of the current before the next resistor.

I = I1 = I2 = ...There is one path, so the same current passes through every part in series.

Each coulomb transfers some energy in each part it passes through. The energy per coulomb for the whole path is the sum of the energy per coulomb in each part. So the p.d.s add up.

Vs = V1 + V2 + ...The same current does not mean the same p.d. A bigger resistance takes a bigger p.d.

Add the resistances

For two resistors with the same current, V1 = IR1 and V2 = IR2. Adding these gives Vs = I(R1 + R2). So the pair acts like one resistor of R1 + R2.

Rseries = R1 + R2 + ...Adding a resistor in series always increases the total resistance.

One path: the same current, and the p.d.s add

The resistances are fixed, the wires have no resistance and the cell is ideal. The arrows show the direction of the current, not its size.

One path: same current through both resistors

One path: same current through both resistorsAn ideal 6.0 V cell drives a current round one closed path: R1: 2 ohm between A and B, then R2: 4 ohm between B and C. The same 1.0 A passes through both. The p.d. across A and B is 2.0 V, and across B and C it is 4.0 V. The switch at the bottom is closed.+-6.0 VR1: 2 ohmR2: 4 ohm2.0 V4.0 VABCI = 1.0 ASwitch closed

The p.d.s 2.0 V and 4.0 V add up to 6.0 V. The current is 1.0 A everywhere in the single path.

Open the only path

Open the only pathThe switch at the bottom is open, so the only path is broken. The current is zero everywhere, and each resistor has 0 V across it. The ideal cell still has 6.0 V, so the gap in the open switch has 6.0 V across it.+-6.0 VR1: 2 ohmR2: 4 ohm0 V0 VCurrent = 0 AOpen switch: 6.0 V across the gap

No current does not mean no p.d. The only path is broken, but the cell still has 6.0 V.

The closed 6.0 V circuit has one path through 2.0 Ω and 4.0 Ω. The current is 1.0 A, and the p.d.s are 2.0 V and 4.0 V. In the second drawing the switch is open: there is no current, but the cell still has 6.0 V.

One current, two p.d.s

2.0 Ω and 4.0 Ω across 6.0 V

Take the resistances as fixed, the wires as having no resistance, and the cell's p.d. as steady at 6.0 V.

  1. Total resistance = 2.0 + 4.0 = 6.0 Ω.
  2. Current = 6.0/6.0 = 1.0 A, through both resistors.
  3. Across 2.0 Ω: V = 1.0 x 2.0 = 2.0 V.
  4. Across 4.0 Ω: V = 1.0 x 4.0 = 4.0 V.

The p.d.s add up to 6.0 V. Each coulomb transfers 2.0 J in the first resistor and 4.0 J in the second. The current through them has not dropped.

Try it step by step

Work it out in steps: Total resistance in ohm, then Current in A, then p.d. across the first resistor in V.

  1. Problem 1. A 3.0 ohm resistor and a 9.0 ohm resistor are connected in series across a 6.0 V supply. Find the current and the p.d. across the 3.0 ohm resistor.
  2. Problem 2. A 5.0 ohm resistor and a 15 ohm resistor are in series across a 10 V supply. Find the current and the p.d. across the 5.0 ohm resistor.
  3. Problem 3. An 8.0 ohm resistor and a 4.0 ohm resistor are in series across a 9.0 V supply. Find the current and the p.d. across the 8.0 ohm resistor.
Show the answer

Problem 1.

Total resistance in ohm: R = 3.0 + 9.0 = 12 ohm

Current in A: I = V / R = 6.0 / 12 = 0.50 A

p.d. across the first resistor in V: V = IR = 0.50 x 3.0 = 1.5 V (2 sf)

Problem 2.

Total resistance in ohm: R = 5.0 + 15 = 20 ohm

Current in A: I = 10 / 20 = 0.50 A

p.d. across the first resistor in V: V = 0.50 x 5.0 = 2.5 V (2 sf)

Problem 3.

Total resistance in ohm: R = 8.0 + 4.0 = 12 ohm

Current in A: I = 9.0 / 12 = 0.75 A

p.d. across the first resistor in V: V = 0.75 x 8.0 = 6.0 V (2 sf)

With the same supply p.d., a larger total resistance means a smaller current.

What an open switch changes

Opening the only path stops the current everywhere in the circuit. Each resistor then has V = IR = 0 across it. The cell still has its e.m.f., so the full 6.0 V appears across the gap in the switch.

This is why older Christmas light sets went completely dark when a single bulb failed. Their bulbs were in series, so one failed bulb broke the only path.

No current does not always mean no p.d. An open gap can have a p.d. across it, even though no current flows through it.

Check your understanding

Fixed 3.0 ohm and 6.0 ohm resistors are in series across an ideal 9.0 V source. What is the potential difference across the 6.0 ohm resistor?

  1. 4.5 V
  2. 6.0 V
  3. 9.0 V
Show the answer

6.0 V

Total resistance is 3.0 + 6.0 = 9.0 ohm, so the shared current is 9.0/9.0 = 1.0 A. The 6.0 ohm resistor has V = IR = 1.0 x 6.0 = 6.0 V; the other has 3.0 V.