K323 / 2027
Thermal properties of matter overview

Lesson 5 of 10

Reading a heating curve

  • I can describe melting, solidification, boiling and condensation as energy transfers without a temperature change.Syllabus

    Syllabus K323, 9(d). Describe melting, solidification, boiling and condensation as energy transfers without a temperature change.

Make a guess. You are not marked.

Crushed ice at -10 degrees C is stirred and heated steadily. A thermometer in the ice is read every minute. What does the reading do once the ice starts to melt?

  1. It falls for a while, because melting uses up the energy in the ice.
  2. It stays at 0 degrees C until all the ice has melted.
  3. It keeps rising at the same rate, because the heater still supplies energy.
Show the answer

It stays at 0 degrees C until all the ice has melted.

While the ice melts, the energy supplied changes the arrangement of the particles. It does not raise their average kinetic energy, so the temperature stays at the melting point.

During a change of state, energy changes how the particles are arranged. That changes their potential energy. Their average random kinetic energy stays the same, and so does the temperature.

A flat part on a temperature-time graph shows a change of state. Energy still enters, but the temperature stays constant until the change is complete.

The values below are model values for a pure sample at a constant pressure. Its melting point is 50°C, and energy keeps entering for the whole six minutes. They are not measurements of a named material.

Temperature while energy continues to enter the sample
Time / minTemperature / °C
020
135
250
350
450
565
680

Energy continues entering during the melting plateau

Supplied idealised data for an unspecified pure substance at constant pressure. Its melting point is 50 °C.

Temperature rises, stays at 50 degrees Celsius during melting, then rises againA temperature-time graph uses supplied model readings. At times zero, one, two, three, four, five and six minutes, temperatures are 20, 35, 50, 50, 50, 65 and 80 degrees Celsius. From zero to two minutes the solid warms. Melting occurs from two to four minutes at 50 degrees Celsius. From four to six minutes the liquid warms. Energy enters throughout; the plateau does not mean the heater stops. The shaded time interval marks melting, without assigning a fraction melted at a particular time.Temperature / °C020406080012345650Melting50 °CTime / min

0-2 min: the solid warms from 20 to 50 °C.

2-4 min: solid changes to liquid at 50 °C. Energy transfer continues.

4-6 min: the liquid warms from 50 to 80 °C.

The temperature rises to 50°C, stays there from 2 to 4 min while the sample melts, then rises again as the liquid warms. Energy keeps entering during the flat part of the graph.
  1. 0 to 2 min: the solid warms from 20°C to 50°C. The average kinetic energy of its particles rises.
  2. 2 to 4 min: melting takes place at 50°C. The amount of liquid rises and the amount of solid falls. Internal energy rises while the average random kinetic energy stays the same.
  3. After 4 min: the sample is liquid and its temperature rises. The average kinetic energy of its particles rises again.

Worked explanation

Why does the reading stay at 50°C?

At 3 min, the sample is still melting. The energy that keeps entering changes how the particles are arranged, and their potential energy, as more solid becomes liquid. It does not raise the average random kinetic energy during this change of state, so the temperature stays at 50°C.

The flat part does not show that the heater has stopped or that the particles have stopped moving. Temperature and total internal energy are different quantities.

Explain the reverse process

If energy is removed from the same liquid, it first cools to its solidification temperature. It then solidifies at the same fixed pressure. Energy keeps leaving and the amount of solid grows, but the temperature stays constant until the change is complete.

The same reasoning works for boiling and condensation at the boiling/condensation temperature for that pressure. Boiling needs energy to keep entering while liquid becomes gas. Condensation transfers energy out while gas becomes liquid. A constant temperature does not mean the transfer has ended.

The readings are only as good as where the thermometer sits and how fast it responds.Measuring temperature explains how to place and read it.

State the plateau conditions. This explanation is for a pure substance that changes state at fixed pressure. It does not claim that every mixture melts at one sharp temperature. Nor does it claim that all warming must include a flat part.

Check your understanding

A pure sample melts at 50 degrees C at constant pressure while energy continues to enter. Which particle explanation accounts for its constant temperature?

  1. Its arrangement and potential energy change while the average random kinetic energy stays the same.
  2. Its particles stop moving while the solid melts, so their kinetic energy cannot rise.
  3. Its internal energy stays unchanged because the temperature stays unchanged.
Show the answer

Its arrangement and potential energy change while the average random kinetic energy stays the same.

Energy entering during melting changes the state and the particle-interaction contribution to internal energy. The particles keep moving; the unchanged average random kinetic energy corresponds to the constant temperature.

A cooling curve shows the reverse change, with energy leaving the sample.