K323 / 2027
Thermal properties of matter overview

Lesson 9 of 10

Measuring specific latent heat

  • I can apply energy transfer for a change of state = mass x specific latent heat.Syllabus

    Syllabus K323, 9(g). Apply energy transfer for a change of state = mass x specific latent heat.

Make a guess. You are not marked.

A funnel of crushed ice at 0 degrees C stands in a warm room. There is no heater. A beaker stands under the funnel. What is in the beaker after 5 minutes?

  1. Some water, because the warm room melts some of the ice.
  2. Nothing, because ice at 0 degrees C cannot melt without a heater.
  3. Nothing, because the ice must first warm above 0 degrees C before it melts.
Show the answer

Some water, because the warm room melts some of the ice.

Energy transfers from the warmer room to the ice. Ice at its melting point melts as soon as it takes in energy. An experiment with a heater must allow for this extra meltwater.

To measure the specific latent heat of fusion of ice, melt ice with a heater of known power. Then find the extra mass that the heater melted.

E = ml links the energy supplied at the melting point to the mass that melts. Rearranged, l = E / m.

Determine specific latent heat of fusion

Use ice already at its melting point, with a heater that transfers energy at a known constant rate. Collect the liquid produced over a measured time and measure its mass. Ice also melts because the surroundings are warmer than it. So not all the collected meltwater need be due to the heater.

  1. Make sure the ice is melting: let the ice reach its melting point and drain away any water already there before the timed collection. Keep some ice present for the whole timed run so that the process stays melting.
  2. Measure meltwater mass: collect the water in a dry weighed container. Subtract its empty mass from its final mass. A balance reading that includes the container is not the mass that melted.
  3. Estimate background melting: use a matched unpowered ice setup over the same time. Match the surroundings, the exposed shape, the starting conditions and the collection method as closely as you can.
  4. Separate the heater's part: estimate the extra mass melted by the heater as mheated - mcontrol. Use the mass unit that matches the unit you want for l.
  5. Relate energy and mass: suppose apparatus warming and other differences are small enough to ignore, or have been corrected. Then lf = Pt / (mheated - mcontrol).

Supplied practical data

Separate heater melting from background melting

A 16.7 W heater runs for 200 s. The powered setup produces 14.0 g of collected meltwater. A matched unpowered control produces 4.0 g. Both contain ice at its melting point the whole time. Assume the background heating is equal. Assume too that you can ignore apparatus warming during collection, and energy lost from the heater or leads outside the melting region.

  1. Heater energy: E = 16.7 x 200 = 3340 J.
  2. Extra melted mass: 14.0 - 4.0 = 10.0 g = 0.0100 kg.
  3. Specific latent heat: lf = 3340 / 0.0100 = 334000 J/kg.

The 4.0 g correction estimates melting due to the surroundings. It does not, by itself, account for energy that leaves the heater through its leads or warms another part of the apparatus.

The control is an estimate. It does not correct for every transfer. It must get the same background heating as the heated setup. Meltwater left behind, or water from the start included by mistake, can change the result. So can apparatus warming and a changing heater output. Repeats help show variation, but they do not fix an unmatched control or a wrong energy account.

Subtract the ice that the room melted. If you ignore background melting, too much mass seems to have melted because of the heater. Dividing the heater's energy by this larger mass gives a value of lf that is too low.

Check your understanding

A student finds the specific latent heat of fusion of ice with a heater in a funnel of melting ice. She has no control funnel, so she uses all the meltwater collected as the mass melted by the heater. Which of these describes her value?

  1. Too low, because the room also melted some ice.
  2. Correct, because the heater energy Pt is known exactly.
  3. Too high, because the room supplied extra energy to the ice.
Show the answer

Too low, because the room also melted some ice.

The mass collected is larger than the mass the heater melted. Dividing the heater energy by a mass that is too large gives a value that is too low.

Practise an exam question

Write your answer first, then tick the mark points it makes.

Exam-style question

A 2.0 kW kettle keeps water boiling. In 3.0 minutes, the mass of water in the kettle falls by 0.15 kg. Calculate the specific latent heat of vaporisation of water from these results, and state one assumption you made. [4]

Saved on this browser only. Anyone using this browser can see it.