9478 / 2027
Circuits overview

Lesson 10 of 15

Loading a potential divider

  • I can solve one-source series/parallel circuits, including potential dividers using NTC thermistors and LDRs.Syllabus

    Syllabus 9478, 16(j). Solve one-source series/parallel circuits, including potential dividers using NTC thermistors and LDRs.

Make a guess. You are not marked.

Two 1.0 megohm resistors divide a 10 V supply. A voltmeter of resistance 10 megohm is connected across the lower one. What does it read?

  1. Exactly 5.0 V, because a voltmeter takes no current.
  2. A little less than 5.0 V: about 4.8 V.
  3. More than 5.0 V, because the meter adds resistance.
Show the answer

A little less than 5.0 V: about 4.8 V.

The meter is in parallel with the lower resistor: 1.0 and 10 megohm give 0.91 megohm. The output is 10 x 0.91/1.91 = 4.8 V.

Anything connected across a divider's output is in parallel with the lower arm. It lowers that arm's resistance, so the output falls.

Two 4.0 kΩ resistors across 8.0 V give an output of 4.0 V. Now connect a 4.0 kΩ load across B and C. It is in parallel with the lower resistor, not in series with the divider.

The load is another B/C branch

The load is another B/C branchAn eight-volt source drives a four-kilohm upper resistor from A to B. Both the four-kilohm lower divider resistor and a separate four-kilohm load join B to C in parallel.+-ABC8.0 V4 kΩ4 kΩLoad4 kΩ1.333 mASame B/C p.d. across both branches

The parallel load changes the lower equivalent resistance. Output is 2.67 V; each lower branch carries about 0.667 mA.

The load and the lower resistor both join B to C, so the current through the upper resistor splits between them.

Worked loaded divider

Rlower = (4.0 × 4.0)/(4.0 + 4.0) = 2.0 kΩ
VBC = 8.0 × 2.0/(4.0 + 2.0) = 2.67 V

The supply current is 8.0/6000 = 1.33 mA, and it splits equally between the two lower branches. The output has fallen from 4.0 V to 2.67 V.

A voltmeter is a load too. If its resistance is much larger than the lower arm, it hardly changes the output. If not, it lowers the reading. So choose a meter with a high resistance for high-resistance circuits.

A real example. Fluke's datasheet for its 117 multimeter gives an input impedance of more than 10 MΩ on its d.c. voltage range. Across a 1 kΩ resistor, that hardly matters. Across a 1 MΩ resistor, it lowers the reading noticeably.

Do not put the load in series with the lower resistor. It joins the same two points, B and C, so it is in parallel.

Check your understanding

Two 4.0 kilohm divider arms connect across an ideal fixed 8.0 V supply. A 4.0 kilohm load is then connected across the lower arm B/C. What is V_B - V_C?

  1. 5.33 V
  2. 4.0 V
  3. 2.67 V
Show the answer

2.67 V

The lower arm and load are parallel, giving 2.0 kilohm. The new output is 8.0 x 2.0/(4.0 + 2.0) = 8/3 V.