K223 / K224 / 2027
Practical electricity overview

Lesson 2 of 8

Measuring electrical power

  • I can recall and apply P = VI and E = VIt in new situations.Syllabus

    Syllabus K223 / K224, 12(b). Recall and apply P = VI and E = VIt in new situations.

Make a guess. You are not marked.

A lamp is in series with a resistor across a supply. To find the lamp's power, a student puts the voltmeter across the supply instead of across the lamp. Is her answer for the power too big, too small or right?

  1. Right, because the current is the same everywhere in a series circuit.
  2. Too small, because some energy is lost in the wires.
  3. Too big, because the supply p.d. is larger than the lamp's p.d.
Show the answer

Too big, because the supply p.d. is larger than the lamp's p.d.

The supply p.d. is shared between the lamp and the resistor. Using the whole supply p.d. with the lamp's current gives the power of both parts together, which is more than the lamp's power.

In short

  • Put an ammeter in series with the part to measure the current through it.
  • Put a voltmeter across the same part to measure the p.d.
  • Multiply the two readings: P = VI. Then E = Pt.

To find the power of a part, measure the current through it and the p.d. across it at the same time. Then multiply them: P = VI.

An ammeter goes in series with the part. A voltmeter goes across it, in parallel. Energy is power x time: E = Pt.

Measure the p.d. across the part and the current through it

The ammeter A is in series with the part. The voltmeter V is joined across the part's two ends, P and Q.

Measuring the current through a part and the p.d. across itA low-voltage d.c. supply is on the left. Ammeter A is in the top wire, in series with a part joined between P and Q. The voltmeter is joined across P and Q. The ammeter reads 0.40 A and the voltmeter reads 6.0 V. The switch at the bottom is closed.+-D.c. sourceA+-0.40 AComponentPQV+-6.0 V across P/QSwitch closed

The voltmeter takes almost no current, so the ammeter reading is the current through the part.

The readings stay at 6.0 V and 0.40 A for 180 s.

For this part, P = VI = 6.0 x 0.40 = 2.4 W. In 180 s it transfers E = Pt = 2.4 x 180 = 432 J.

Taking the readings

  1. Use a low-voltage supply, never the mains.
  2. Join the ammeter in series with the part, and the voltmeter across it.
  3. Choose meter ranges that the readings will fit. Write down each reading with its unit.
  4. Time how long the current flows. Check the readings now and then, because a part that warms up can change its current.
  5. Work out P = VI from readings taken at the same time. Then find E = Pt.

James Joule measured the heating from a current in this way. In 1840 he published his finding that a current can heat a wire. He put a wire in water, passed a known current through it for 30 minutes and measured how much the water warmed.

More detail (optional)

If the current changes as the part warms up, use the average power over the time in E = Pt. If the p.d. stays fixed, you can use the average current in E = VIt.

Power is V x I, not V / I. 6.0 / 0.40 = 15 is the resistance in ohms, not the power in watts.

Check your understanding

A low-voltage component has a steady 6.0 V across it and 0.40 A through it for 180 s. Which result describes its electrical input?

  1. Power is 2.4 W and input energy is 2.4 J.
  2. Power is 2.4 W and input energy is 432 J.
  3. Power is 15 W and useful output energy is 2700 J.
Show the answer

Power is 2.4 W and input energy is 432 J.

P = VI = 6.0 x 0.40 = 2.4 W. E = Pt = 2.4 x 180 = 432 J. These readings describe electrical input; they do not determine how much becomes a particular useful output.