Lesson 7 of 11
Uncertainty in products, quotients and powers
I can assess derived uncertainty by adding absolute or relative uncertainties, or by numerical substitution.Syllabus
Syllabus 8867, 1(g). Assess derived uncertainty by adding absolute or relative uncertainties, or by numerical substitution.
When you multiply or divide measurements, add their fractional or percentage uncertainties. A quantity raised to a power n counts n times.
- Multiply or divide: add fractional uncertainties
- For q = xy or q = x/y, Δq/q = Δx/x + Δy/y. You can add percentages in the same way.
- A power: multiply by the power
- For q = xn, Δq/q = |n| Δx/x. A squared diameter counts twice, even when it is on the bottom of a fraction.
- An exact number: adds nothing
- Numbers such as 4 and π in a formula are exact, so they add no uncertainty.
A real example. Some physical constants are exact too. The SI fixes the speed of light at exactly 299 792 458 m s-1, by definition. In a calculation, it adds no uncertainty, just like π.
Worked quotient
Speed from a distance and a time
A runner covers L = (10.00 ± 0.02) m in t = (2.50 ± 0.05) s. Find v = L/t and its uncertainty.
- Value: v = 10.00 / 2.50 = 4.00 m/s.
- Add fractional uncertainties: Δv/v = 0.02/10.00 + 0.05/2.50 = 0.002 + 0.020 = 0.022.
- Back to absolute: Δv = 4.00 × 0.022 = 0.088 m/s.
- Round: (4.00 ± 0.09) m/s.
The time gives 2.0% and the distance only 0.2%. Better timing would help most.
Try it step by step
Work it out in steps: Fractional uncertainty in d, then Fractional uncertainty in t, then Absolute uncertainty in v = d / t in m/s.
Show the answer
Problem 1.
Fractional uncertainty in d: 0.01 / 2.00 = 0.005
Fractional uncertainty in t: 0.02 / 0.80 = 0.025
Absolute uncertainty in v = d / t in m/s: v = 2.50 m/s; fractional uncertainties add for a quotient: 0.030, so the uncertainty is 2.50 x 0.030 = 0.08 m/s (v = 2.50 +/- 0.08 m/s)
Problem 2.
Fractional uncertainty in d: 0.1 / 5.0 = 0.02
Fractional uncertainty in t: 0.1 / 2.0 = 0.05
Absolute uncertainty in v = d / t in m/s: v = 2.5 m/s; uncertainty = 2.5 x 0.07 = 0.2 m/s to 1 sf (v = 2.5 +/- 0.2 m/s)
Problem 3.
Fractional uncertainty in d: 0.02 / 1.50 = 0.013
Fractional uncertainty in t: 0.02 / 0.50 = 0.040
Absolute uncertainty in v = d / t in m/s: v = 3.0 m/s; uncertainty = 3.0 x 0.053 = 0.2 m/s to 1 sf (v = 3.0 +/- 0.2 m/s)
Check by numerical substitution
You can also put the extreme values into the formula. For v = L/t, a bigger L raises v, but a bigger t lowers it. So use the largest L with the smallest t:
vmax = 10.02 / 2.45 = 4.090 m/s
vmin = 9.98 / 2.55 = 3.914 m/s
Both are close to 4.00 ± 0.09 m/s, which supports the rule. Putting every input at its maximum would not give the largest quotient.
Worked power and quotient
Which cylinder measurement matters most?
A cylinder's density is ρ = 4m / (πd2L), where m is its mass, d its diameter and L its length.
| Quantity | Value and absolute uncertainty |
|---|---|
| Mass m | (0.0500 ± 0.0001) kg |
| Diameter d | (0.0200 ± 0.0002) m |
| Length L | (0.100 ± 0.001) m |
The central values give ρ = 1591.55 kg/m3 before rounding. The fractional uncertainties are:
- Mass: 0.0001/0.0500 = 0.002.
- Diameter, squared: 2 × (0.0002/0.0200) = 0.020.
- Length: 0.001/0.100 = 0.010.
Total = 0.032, or 3.2%. So Δρ = 1591.55 × 0.032 = 50.9 kg/m3. Report (1.59 ± 0.05) × 103 kg/m3.
The diameter gives 2.0%, the length 1.0% and the mass 0.2%. Measuring the diameter better would help most.
Keep extra digits while you work. At the end, round the uncertainty to 1 significant figure. Then round the value to the same decimal place, as in (1.59 ± 0.05) × 103.
The simple rules need small fractional uncertainties. If they are large, or a bottom value could reach zero, use numerical substitution instead.
Check your understanding
For density rho = 4m/(pi d2 L), the percentage uncertainties in m, d and L are 0.2%, 1.0% and 1.0%. Which single improvement most reduces the estimated density uncertainty?
Show the answer
Halve the percentage uncertainty in diameter.
The current contributions are 0.2% + 2(1.0%) + 1.0% = 3.2%. Halving the diameter uncertainty changes its contribution from 2.0% to 1.0%, giving the largest reduction.
Practise an exam question
Write your answer first, then tick the mark points it makes.
Exam-style question
The diameter of a wire is measured as (0.50 ± 0.01) mm. Calculate the percentage uncertainty in the cross-sectional area of the wire. [2]
Saved on this browser only. Anyone using this browser can see it.