Lesson 4 of 7
Refractive index and the sine ratio
I can apply the constant sine ratio to new situations and calculations.Syllabus
Syllabus K326 / K327, 11(d). Apply the constant sine ratio to new situations and calculations.
I can define refractive index as the ratio of vacuum light speed to speed in the medium.Syllabus
Syllabus K326 / K327, 11(e). Define refractive index as the ratio of vacuum light speed to speed in the medium.
The refractive index of a medium tells you how much it slows light. It also fixes how far a ray bends, through the ratio sin i / sin r.
In refraction, a ray bends towards the normal when light slows down. It bends away when light speeds up.
Refractive index and speed
For the same light, a higher refractive index means a lower speed. It does not mean the material has a greater mass density.
The speed of light in a vacuum is about 3.0 x 108 m/s. Air slows light very little, so its refractive index is taken as 1. Water has n of about 1.33, common glass about 1.5 and diamond about 2.42.
Speed and index
Light travels at 2.0 x 108 m/s in a material
Use the speed in a vacuum, 3.0 x 108 m/s:
n = (3.0 x 108)/(2.0 x 108) = 1.50.
Keep both speeds in the same unit. The answer is 1.50, not 1.50 m/s.
Check your understanding
The speed of light in a vacuum is 3.0 x 108 m/s. Water has a refractive index of 1.33. What is the speed of light in water?
Show the answer
About 2.3 x 108 m/s.
n = c / v, so v = c / n = 3.0 x 108 / 1.33 = 2.3 x 108 m/s. Light is slower in water than in a vacuum.
Use the sines of the angles
Take one pair of media and the same light. Then sin i / sin r is constant, as long as you say which way the light travels. If the first medium has index n1 and the second has n2, the constant is n2/n1.
This rule is known as Snell's law. It is named after Willebrord Snellius, who worked it out in 1621. Ibn Sahl had found it in Baghdad by 984.
Entering the material
From air into n = 1.50 at i = 45°
- Choose the direction: air is the first medium and the material is the second.
- Rearrange: sin r = sin 45°/1.50 = 0.4714.
- Use inverse sine in degree mode: r = 28.1°.
The angle is smaller, which fits bending towards the normal. Do not divide 45° by 1.50. The rule uses the sines, not the angles.
| Incidence i | sin r = sin i / 1.50 | Refraction r |
|---|---|---|
| 30° | 0.3333 | 19.5° |
| 45° | 0.4714 | 28.1° |
| 60° | 0.5774 | 35.3° |
Leaving the material
From n = 1.50 into air at i = 30° inside the material
Now n1 = 1.50 and n2 = 1:
sin r = 1.50 sin 30° = 0.750; r = 48.6°.
The ray bends away from the normal. The refractive index of the material is still 1.50. Reversing the ray turns the sine ratio over. It does not change n = c/v.
Try it step by step
Work it out in steps: sin i, then sin r = sin i / n, then Angle of refraction r in degrees.
Show the answer
Problem 1.
sin i: sin 30 = 0.500
sin r = sin i / n: sin r = 0.500 / 1.33 = 0.376
Angle of refraction r in degrees: r = inverse sin of 0.376 = 22.1 degrees, which is 22 degrees to 2 sf
Problem 2.
sin i: sin 50 = 0.766
sin r = sin i / n: sin r = 0.766 / 1.50 = 0.511
Angle of refraction r in degrees: r = inverse sin of 0.511 = 30.7 degrees, which is 31 degrees to 2 sf
Problem 3.
sin i: sin 40 = 0.643
sin r = sin i / n: sin r = 0.643 / 1.33 = 0.483
Angle of refraction r in degrees: r = inverse sin of 0.483 = 28.9 degrees, which is 29 degrees to 2 sf
Label the first and second media before you substitute. The short form n = sin i / sin r is for light going from air into the material. Do not use it unchanged for a ray that leaves the material.
Check your understanding
Light enters a material of refractive index 1.50 from air at 45 degrees to the normal. Taking the refractive index of air as 1, which calculation gives the refracted angle?
Show the answer
Inverse sine of (sin 45/1.50), giving 28.1 degrees.
For air into this material, 1.50 = sin i/sin r. Rearranging gives sin r = sin 45/1.50 = 0.4714, so r = 28.1 degrees. This smaller angle agrees with bending towards the normal.