K223 / K224 / 2027
Physical quantities and measurement overview

Lesson 4 of 7

Making useful measurements

  • I can choose and explain measuring instruments and methods with suitable range and precision, including the linked quantity-specific determinations.Syllabus

    Syllabus K223 / K224, 1(e). Choose and explain measuring instruments and methods with suitable range and precision, including the linked quantity-specific determinations.

Make a guess. You are not marked.

You want the thickness of one sheet of paper using a ruler marked in millimetres. What is the best method?

  1. Fold one sheet many times and measure the folded edge.
  2. Measure a stack of 100 sheets and divide the thickness by 100.
  3. Measure one sheet very carefully against the finest ruler marks.
Show the answer

Measure a stack of 100 sheets and divide the thickness by 100.

One sheet is far thinner than 1 mm, so a ruler cannot read it. A stack of 100 is several millimetres thick, and dividing by 100 gives one sheet.

In short

  • To measure something very thin, measure many together and divide, for example a stack of 100 sheets.
  • Read a rule at both ends of the object and subtract. Look straight at the scale.
  • Check that the instrument reads zero first. If it does not, correct every reading.

A useful measurement depends on how you take the reading, not just which instrument you choose.

Choose a suitable range and resolution first. Then look for a specific source of error and a method that addresses it.

A source of error is anything that makes a reading differ from the true value. This lesson deals with three: a worn or offset starting point, a slanted line of sight and a display that does not start at zero.

Read the difference between the ends

Place a rule parallel and close to the length being measured. If the object does not start at zero, read both ends and subtract. This is also useful when a rule's zero end is worn.

Measuring from a non-zero ruler readingThe left end of an object is at 2.0 cm and the right end is at 17.8 cm. The length is the difference, 15.8 cm, not the final reading alone.2.0 cm17.8 cmObject05101520Scale readings in cm
The supplied end readings are 2.0 cm and 17.8 cm. Length = 17.8 - 2.0 = 15.8 cm. The final reading alone is not the object's length.

Look perpendicularly at the scale. If the object and markings are at slightly different heights, looking from one side makes them appear to line up differently. This is parallax error. Keep the object close to the scale as well as placing your eye correctly.

Looking perpendicularly at a ruler scaleThe end of an object is slightly above a ruler. An eye directly above that end sees the correct mark. Looking at an angle aligns it with a different mark and causes a parallax error.At an angleDirectly aboveObjectCorrectmarkApparentmarkRuler
Side view: the eye directly above the object's end reads the correct mark. An angled line of sight crosses the scale at a different mark.

Check the zero before trusting the display

Clean and gently close the jaws of digital calipers, then check the reading. If they correctly close with no object between them but the display is not zero, there is a zero offset. Use the instrument's zero control when appropriate, or correct a stated stable offset.

Worked example

Correcting a positive zero error

Closed calipers read +0.02 mm. With an object between the jaws, they read 3.42 mm. Assume the zero offset stays the same.

Corrected reading = displayed reading - zero offset
= 3.42 - (+0.02) = 3.40 mm

The instrument adds 0.02 mm even when the true gap is zero, so subtract that extra amount. The same rule uses the sign of the offset: subtracting a negative zero offset would increase the reading.

More detail (optional)

Repeating a reading does not remove a stable zero error. Repeats help you judge and reduce random variation through averaging. A consistent offset needs a correction or a properly adjusted instrument.

Other common measurements

Match the method to the quantity
QuantityInstrument and useful precaution
MassUse a balance with a suitable range. Check its zero; tare an empty container before adding the material, or subtract the container's mass.
Time intervalUse a stopwatch or suitable timer. Define the starting and finishing events clearly; use repeated events when one interval is too short to time reliably by hand.
TemperatureUse a thermometer or temperature probe. Put the sensing part in good contact with the material as instructed and wait for a steady reading. In a liquid, avoid resting the sensor against the container.
Liquid volumeUse a measuring cylinder of suitable capacity and divisions. Keep it upright and read the water meniscus at eye level.

To record readings in a table and plot them, see practical skills. When one reading is too small or awkward to take directly, see timing swings and measuring volume.

Some quantities are calculated from several measurements. For example, measuring distance and elapsed time lets you calculate average speed. The examples below apply the same measurement principles to particular quantities.

Find a method for a particular quantity

Check your understanding

Closed digital calipers read -0.03 mm. With a coin between the jaws they read 1.82 mm. Which of these is the corrected thickness of the coin?

  1. 1.79 mm
  2. 1.82 mm
  3. 1.85 mm
Show the answer

1.85 mm

Corrected reading = displayed reading - zero offset = 1.82 - (-0.03) = 1.85 mm. The calipers read 0.03 mm too low, so the true thickness is larger than the display shows.