Full chapter
Electric charge and current of electricity
All 6 topics and the revision summary on one page.
01
Electric charge and interactions
Make a guess. You are not marked.
A plastic rod rubbed with a cloth becomes negatively charged. What has moved?
Show the answer
Electrons, which have moved from the cloth onto the rod.
Rubbing transfers electrons. The rod gains electrons and becomes negative; the cloth loses them and is left equally positive.
In short
- There are two kinds of charge, positive and negative.
- Like charges repel; unlike charges attract.
- Rubbing moves electrons from one object to the other.
Electric charge comes in two kinds: positive and negative. Charged objects push or pull on each other without touching.
Charge has the symbol q or Q. It is measured in coulombs, C. Benjamin Franklin chose which kind to call positive: the charge a glass rod gets when it is rubbed with silk.
Neutral does not mean no charged particles
Atoms contain protons, which are positive, in their nuclei. They also contain electrons, which are negative. A neutral object has equal amounts of positive and negative charge, so its net charge is zero. Net charge is what is left over when the two are added.
An object with extra negative charge has a negative net charge. An object with extra positive charge has a positive net charge. The sign tells you which kind there is more of. It does not mean that the object is made only of protons or only of electrons.
Predict attraction and repulsion
Predict the electric force on each charged object
These small objects carry the shown net charges. Only their electric forces on one another are shown; orange arrows are forces, not motion.
What the observation shows
Two charged balls repel
They have the same sign. They could both be positive or both be negative. Repulsion alone does not tell you which.
Now suppose one ball also repels a charge that is known to be positive. That extra test shows that the ball is positive.
Attraction can have more than one cause. A charged object attracts an object with the opposite charge. It can also attract a neutral object. So attraction alone does not prove that the two objects have opposite charges.
Check your understanding
Two small charged balls, separately suspended and isolated from other charged objects, repel. What can be concluded about their charge signs?
Show the answer
Same sign, but this test cannot tell positive from negative.
Like charges repel. Both positive and both negative fit the observation. A further comparison with a known charge would be needed to identify the sign.
When charge flows through a wire, the amount that passes a point each second is the electric current.
02
Current, charge and electron flow
In short
- Current is the rate of flow of charge: I = Q/t, in amperes, A.
- Charge = current x time: Q = It, with the time in seconds.
- Conventional current flows from + to -. Electrons in a wire flow the other way.
Current is the rate of flow of charge. It tells you how much charge passes a point in a circuit each second.
Charge is measured in coulombs, C. Electrons carry negative charge. In a metal wire, some electrons are free to move, while the positive ions stay in place.
Electric current is the rate of flow of charge. Its symbol is I, and its unit is the ampere, A. One ampere means one coulomb of charge passes a point each second: 1 A = 1 C/s. So 1 C = 1 A s.
The ampere is named after the French scientist Andre-Marie Ampere. In a current of 1 A, about 6.2 x 1018 electrons pass a point each second.
Picture slicing across a wire at one place. The cut face is a cross-section. A current of 0.30 A means that 0.30 C passes that cross-section each second. It does not mean that the whole wire holds only 0.30 C.
Follow the charge round the circuit
The cell drives a current through the resistor. Green arrows show conventional current. Blue arrows show the electrons. The arrows show direction, not speed.
Steady current: 0.30 A. Time: 2.0 min = 120 s.
Charge passing X: Q = It = 0.30 × 120 = 36 C.
The resistor transfers energy. It does not use up the charge passing through it.
Conventional current and electron flow
Conventional current is the direction in which positive charge would flow. Outside the cell, it flows from the positive terminal, through the circuit, to the negative terminal. On a cell symbol, the long line is the positive terminal.
In a metal wire, the charges that really move are electrons. They are negative, so they flow the opposite way: from the negative terminal to the positive terminal.
Why the two directions? Positive and negative charge were named long before anyone knew about electrons. J. J. Thomson discovered the electron in 1897, and it turned out to be negative.
Electrons drift slowly. In a copper wire with a cross-section of 0.5 mm2 carrying 5 A, they move at only about a millimetre per second. A lamp still lights at once. The wire is already full of free electrons, and they all start to drift as soon as the circuit is closed.
Charge passing a point
A current flows for two minutes
A steady current of 0.30 A flows for 2.0 min. First change the time to seconds: 2.0 x 60 = 120 s.
Q = It = 0.30 x 120 = 36 C.
In another case, 18 C passes a point in 45 s. The average current is I = Q/t = 18/45 = 0.40 A.
If a current is given as 300 mA, change it to amperes first: 300/1000 = 0.300 A. The prefix milli means one thousandth.
Try it step by step
Work it out in steps: Time in s, then Charge Q = It in C.
Show the answer
Problem 1.
Time in s: t = 3.0 x 60 = 180 s
Charge Q = It in C: Q = It = 0.50 x 180 = 90 C (2 sf)
Problem 2.
Time in s: t = 1.5 x 60 = 90 s
Charge Q = It in C: Q = 2.0 x 90 = 180 C (2 sf)
Problem 3.
Time in s: t = 4.0 x 60 = 240 s
Charge Q = It in C: I = 250 mA = 0.25 A, so Q = 0.25 x 240 = 60 C (2 sf)
More detail (optional)
Q = It works when the current is steady. If the current changes, use the average current over the time. Or split the time into steady parts, find the charge for each part, and add them up.
To measure a current, you put an ammeter in the circuit. It reads amperes, not coulombs. To find the charge that passed, also time the current, then use Q = It.
Say "rate of flow of charge". "Current is the flow of electrons" leaves out the rate, so it does not score. Also change minutes to seconds before you use Q = It.
Watch out for this
A student says: "Current is used up as it flows through a lamp, so less current returns to the cell." What is wrong with this?
Show the answer
Charge is not used up. In a series circuit the current is the same at every point. What the lamp takes is energy, which the charge carries from the cell.
Check your understanding
A steady current of 0.30 A flows through a wire for 2.0 min. How much charge passes a marked cross-section?
Show the answer
36 C
The current carries 0.30 C past the cross-section each second. In 120 s, Q = 0.30 x 120 = 36 C.
Check your understanding
A cell drives a current through a lamp. Which of these describes the flow in the connecting wires?
Show the answer
Conventional current goes from the positive terminal to the negative terminal. Electrons drift the opposite way.
Conventional current is the direction positive charge would flow: from + to - outside the cell. Electrons are negative, so in the metal wires they drift from - to +.
03
E.m.f. and potential difference
In short
- E.m.f.: the work done by a source to drive one coulomb of charge round the whole circuit.
- P.d.: the work done to drive one coulomb of charge through one component.
- Both are measured in volts: 1 V = 1 J/C.
Voltage tells you how much energy each coulomb of charge transfers. E.m.f. is about a source and the whole circuit. Potential difference is about one component.
Work done is energy transferred, in joules, J. Current counts the coulombs that pass each second. Voltage counts the joules for each coulomb.
- Electromotive force (e.m.f.)
- The e.m.f. of a source is the work done by the source in driving a unit charge around a complete circuit. A unit charge means one coulomb. E.m.f. is measured in volts. A cell with an e.m.f. of 1.5 V does 1.5 J of work on each coulomb it drives round the circuit.
- Potential difference (p.d.)
- The p.d. across a component is the work done in driving a unit charge through the component. It is also measured in volts. A p.d. of 3.0 V across a lamp means 3.0 J is transferred in the lamp for each coulomb that passes through it.
The volt is named after the Italian scientist Alessandro Volta. A fresh alkaline cell, such as an AA cell, is rated at 1.5 V. Small voltages may be given in millivolts: 1 mV = 0.001 V.
Inside a cell, energy moves from its chemical store to the charges. In a resistor, that energy heats the resistor. In a motor, some of it can lift a load. The charge itself keeps flowing round the circuit, and only energy is passed on. See energy stores and transfers.
Energy per coulomb
Find the p.d. across a component
A component transfers 60 J of energy when 12 C passes through it.
P.d. = W/Q = 60/12 = 5.0 J/C = 5.0 V.
Another component has a p.d. of 3.0 V across it, and 8.0 C passes through it. The work done is W = VQ = 3.0 x 8.0 = 24 J.
Try it step by step
Work it out in steps: Charge Q = It in C, then Energy transferred E = VQ in J.
Show the answer
Problem 1.
Charge Q = It in C: Q = It = 0.20 x 50 = 10 C
Energy transferred E = VQ in J: E = VQ = 6.0 x 10 = 60 J (2 sf)
Problem 2.
Charge Q = It in C: Q = 1.5 x 40 = 60 C
Energy transferred E = VQ in J: E = 12 x 60 = 720 J (2 sf)
Problem 3.
Charge Q = It in C: Q = 0.40 x 25 = 10 C
Energy transferred E = VQ in J: E = 3.0 x 10 = 30 J (2 sf)
To measure a p.d., connect a voltmeter across the component.
E.m.f. is not a force. Despite its name, it is measured in volts, not newtons. Like p.d., it is energy per coulomb.
Check your understanding
A component transfers 60 J of energy when 12 C passes through it. What is the potential difference across it?
Show the answer
5.0 V: each coulomb transfers 5.0 J in the component.
Potential difference is work done per unit charge: V = 60 / 12 = 5.0 J/C = 5.0 V. It is an energy-per-charge quantity, not a rate.
Check your understanding
A cell has an e.m.f. of 1.5 V. Which of these statements about the cell is correct?
Show the answer
It does 1.5 J of work on each coulomb it drives round the circuit.
E.m.f. is the work done by a source in driving a unit charge around a complete circuit. 1.5 V means 1.5 J for each coulomb.
04
Ammeters and voltmeters
Make a guess. You are not marked.
By mistake, a student connects a voltmeter in series with a lamp and a cell. The voltmeter has a very high resistance. What happens?
Show the answer
The lamp stays off, because almost no current can flow through it.
The voltmeter's very high resistance is now in the only path, so the current is tiny. The lamp needs a much larger current to glow.
In short
- An ammeter measures current. Connect it in series with the component.
- A voltmeter measures p.d. Connect it in parallel, across the component.
- Pick a range bigger than the reading you expect.
An ammeter goes in series to measure the current through a component. A voltmeter goes in parallel, across the component, to measure the p.d.
Current is the charge passing a point each second. P.d. is the energy transferred per coulomb between two points.
An ammeter goes in series
An ammeter is drawn as a circle with an A inside. To measure the current through a lamp, break the circuit next to the lamp and put the ammeter in the gap. Now all of the lamp's current passes through the meter. This is a series connection: the parts are joined one after another, in one path.
An ammeter has a very low resistance, so it hardly changes the current it measures. Never connect it straight across a cell or a lamp. It would give the current an easy path round them, and a very large current could flow.
A voltmeter goes in parallel
A voltmeter is drawn as a circle with a V inside. Connect one lead to each end of the component. This is a parallel connection: the meter sits across the component, beside the main path.
A voltmeter has a very high resistance, so it takes almost no current. That is why it must not go in series. There, it would let almost no current through, and the lamp would stay off.
Measure current through and p.d. across the same resistor
A is an ammeter in series. V is a voltmeter joined to the two ends of the resistor. The + signs show which way round to connect each meter.
Readings: 0.20 A through the resistor and 6.0 V across it.
We treat both meters as ideal. The voltmeter takes almost no current, and the ammeter has almost no p.d. across it. So the ammeter reads the current in the resistor.
Get the connections and the range right
For d.c., join each meter's + terminal to the side nearer the cell's + terminal. On a meter with a needle, a needle that tries to go below zero means the leads are swapped.
Pick a range bigger than the reading you expect. A 0-5 V range cannot show 6.0 V. If you are unsure, start on the largest range. Then switch down to the smallest range that still fits, for a more exact reading.
Read a needle scale with your eye straight in front of the needle. This avoids parallax error, a wrong reading caused by looking at the scale from an angle.
Early current meters used an effect found by Hans Christian Oersted in 1820. A current in a wire makes a nearby compass needle turn. Today one digital multimeter can be set to work as an ammeter or a voltmeter.
Do not swap the meters. A voltmeter in series stops the current. An ammeter across a component lets a large current flow round it.
Check your understanding
Which of these connections measures the current through a lamp and the p.d. across it?
Show the answer
An ammeter in series with the lamp, and a voltmeter joined across the two ends of the lamp.
The lamp's current must pass through the ammeter, so it goes in series. The p.d. is measured between the lamp's two ends, so the voltmeter goes in parallel with the lamp.
05
Resistance
Make a guess. You are not marked.
Two resistors each have 6.0 V across them. Resistor A carries 0.50 A and resistor B carries 0.20 A. Which has the greater resistance?
Show the answer
B, because it lets less current through at the same p.d.
R = V/I. For A, 6.0/0.50 = 12 ohm. For B, 6.0/0.20 = 30 ohm. Less current at the same p.d. means more resistance.
In short
- Resistance R = V/I, measured in ohms, Ω.
- Use the p.d. across a component and the current through that same component.
- At the same p.d., more resistance means less current.
The resistance of a component is the p.d. across it divided by the current through it: R = V/I.
Measure the current I through the component with an ammeter, in amperes. Measure the p.d. V across it with a voltmeter, in volts. Use readings taken at the same time.
Resistance tells you how hard it is to drive a current through a component. With the same p.d. across them, a component with more resistance lets less current through.
The ohm is named after the German scientist Georg Ohm. In 1827 he published measurements of voltage and current in simple circuits made with different lengths of wire.
A value of V/I is the resistance for that one reading. If the component heats up, its resistance can change. Then a new p.d. may give a different value of V/I.
Use paired readings
Find the resistance, then the new current
The p.d. across a resistor is 6.0 V and the current through it is 0.20 A.
R = V/I = 6.0/0.20 = 30 Ω.
The p.d. is raised to 9.0 V. If the resistance stays at 30 Ω, the new current is I = V/R = 9.0/30 = 0.30 A.
This assumes that the resistor does not heat up. If it did, its resistance could change and the current would be different.
Try it step by step
Work it out in steps: Resistance R = V / I in ohm, then Current at the new p.d. in A.
Show the answer
Problem 1.
Resistance R = V / I in ohm: R = 4.0 / 0.25 = 16 ohm
Current at the new p.d. in A: I = V / R = 6.0 / 16 = 0.375 A, which is 0.38 A to 2 sf
Problem 2.
Resistance R = V / I in ohm: R = 9.0 / 0.30 = 30 ohm
Current at the new p.d. in A: I = 12 / 30 = 0.40 A (2 sf)
Problem 3.
Resistance R = V / I in ohm: R = 7.5 / 0.50 = 15 ohm
Current at the new p.d. in A: I = 3.0 / 15 = 0.20 A (2 sf)
Measure a resistance
Use a low-voltage supply. Put an ammeter in series with the component and a voltmeter across it. Wait for the readings to settle, then record both together. Work out R = V/I.
Divide V by I, not I by V. For a resistor with 0.25 A at 6.0 V, 0.25/6.0 gives 0.042, far too small. Write R = V/I before you put in the numbers. Use the p.d. and the current of the same component.
Check your understanding
A voltmeter reads 6.0 V across a resistor while an ammeter measures 0.20 A through that resistor. What is its resistance at this operating point?
Show the answer
30 ohm
R = V/I = 6.0 / 0.20 = 30 ohm. The two readings refer to the same resistor. This result alone does not show that its resistance stays constant at other operating points.
06
Resistance of a wire
Make a guess. You are not marked.
A wire has a resistance of 4 ohm. A second wire of the same material and the same thickness is twice as long. What is its resistance?
Show the answer
8 ohm, twice as much.
Resistance is proportional to length for the same material and cross-section. Charge has twice as much wire to pass through, so the resistance doubles.
In short
- A longer wire has more resistance: R is proportional to length.
- A thicker wire has less resistance: R is inversely proportional to cross-sectional area.
- Twice the diameter gives four times the area, so a quarter of the resistance.
A longer wire has more resistance, and a thicker wire has less. For wires of the same material at the same temperature, R is proportional to length and inversely proportional to cross-sectional area.
Resistance is V/I, measured in ohms. Compare wires made of the same material at the same temperature. A change in either one also changes the resistance.
The heating wire in toasters and electric kettles is often nichrome, a mix of nickel and chromium. A nichrome wire has about 66 times the resistance of a copper wire of the same length and thickness.
- Longer wire, more resistance
- Resistance is proportional to length: R ∝ L. Double the length with the same thickness, and the resistance doubles. The charge has twice as much wire to pass through.
- Thicker wire, less resistance
- Resistance is inversely proportional to cross-sectional area: R ∝ 1/A. Double the area with the same length, and the resistance halves. A wider wire gives the charge more room to flow.
The cross-sectional area is the area of the wire's cut end: the circle you see if you slice it across. It is not the curved outside surface. For a round wire, A = πd2/4, so the area depends on the square of the diameter d.
Double the length and double the diameter
Both wires are the same material at the same temperature. The drawings use the same scale. The labels give ratios, not sizes to measure on your screen. The area is the circle at the cut end.
Original wire: 8.0 ohm
Changed wire: 4.0 ohm
Twice the diameter gives four times the cross-sectional area. The resistance changes by 2/4 = 1/2, so 8.0 Ω becomes 4.0 Ω.
One change at a time
Twice the length and twice the diameter
The first wire has a resistance of 8.0 Ω.
- Twice the length multiplies the resistance by 2.
- Twice the diameter gives 22 = 4 times the area. That divides the resistance by 4.
- Together: new R = 8.0 x 2/4 = 4.0 Ω.
In general, for the same material and temperature: Rnew/Rold = (Lnew/Lold) x (Aold/Anew).
Investigate how length affects resistance
Use one wire that has the same thickness all along it. Clip two contacts onto it, and measure the length between them with a ruler. Only this active length carries the current.
- Keep the material and the thickness the same. Use several different active lengths.
- At each length, record the current through that part of the wire and the p.d. across it. Work out R = V/I.
- Keep the current small and switch off between readings. This stops the wire heating up, which would change its resistance.
- Plot R against length. A straight line through the origin shows that R is proportional to length.
More detail (optional)
To find the area, measure the diameter with a micrometer. Check it for zero error, and measure at several places along the wire. Change the diameter to metres before you work out the area.
The contacts and leads can add a little resistance of their own. A wire whose diameter changes along its length is not uniform. Repeat readings show how much they scatter, but they do not remove these effects. Name the problem and say how your method deals with it.
Twice the diameter is four times the area. So doubling the diameter gives a quarter of the resistance, not half.
Check your understanding
A wire has resistance 8.0 ohm. A second wire of the same material and temperature has twice its length and twice its diameter. What is the second resistance?
Show the answer
4.0 ohm: length factor 2, area factor 4.
For the same material and temperature, R is proportional to L/A. The new resistance is 8.0 x 2 / 4 = 4.0 ohm.
Revision summary
Charge and current
Charge is positive or negative and is measured in coulombs, C. Like charges repel; unlike charges attract. A neutral object has equal amounts of positive and negative charge. Attraction alone does not prove that two objects have opposite charges.
- Charge, Q
- Unit: coulomb, C. 1 C = 1 A s. For a steady current, Q = It. Change minutes to seconds and milliamperes to amperes: 1 mA = 0.001 A.
- Current, I
- The rate of flow of charge. Unit: ampere, A = C/s. I = Q/t gives the average current over the time.
- Direction
- Outside the cell, conventional current flows from + to -. Electrons in the wire flow the opposite way. A component transfers energy; it does not use up the charge.
Energy per charge
- E.m.f., E
- The work done by a source in driving a unit charge around a complete circuit. Unit: volt, V = J/C.
- Potential difference, V
- The work done in driving a unit charge through a component. Also in volts. W = VQ. 1 mV = 0.001 V.
Ammeters and voltmeters
Ammeter: in series, with a very low resistance. Voltmeter: in parallel, across the component, with a very high resistance. Join each + terminal to the side nearer the cell's +, and pick a range bigger than the reading you expect.
Resistance and wires
- Resistance, R
- R = V/I; V = IR; I = V/R. Unit: ohm, Ω = V/A. Use the p.d. across and the current through the same component, from the same reading.
- Wire dimensions
- Same material and temperature: R ∝ L and R ∝ 1/A. For a round wire, A ∝ d2. Twice the length and twice the diameter give half the resistance.
- Investigating length
- Measure the active length between the contacts. Keep the current small so the wire stays at the same temperature. Plot R against L: a straight line through the origin.
Practise exam questions
Write your answer first, then tick the mark points it makes.
Exam-style question
A cell is connected to a lamp. Distinguish between the electromotive force (e.m.f.) of the cell and the potential difference (p.d.) across the lamp. [2]
Saved on this browser only. Anyone using this browser can see it.
Exam-style question
Define electric current. A current of 0.40 A flows through a lamp for 5.0 minutes. Calculate the charge that passes through the lamp. [3]
Saved on this browser only. Anyone using this browser can see it.
Exam-style question
Define the resistance of a component. When the potential difference across a resistor is 6.0 V, the current in it is 0.25 A. Calculate its resistance. [3]
Saved on this browser only. Anyone using this browser can see it.
Quick recall
Two small charged balls, separately suspended and isolated from other charged objects, repel. What can be concluded about their charge signs?