9478 / 2027
Superposition overview

Lesson 10 of 13

Measuring wavelength with a grating

  • I can describe the use of a diffraction grating to determine the wavelength of light.Syllabus

    Syllabus 9478, 11(j). Describe the use of a diffraction grating to determine the wavelength of light.

Make a guess. You are not marked.

A grating with 300 lines per mm is replaced by one with 600 lines per mm. The laser stays the same. What happens to the first-order spots?

  1. They move closer to the centre, because the lines are packed more tightly.
  2. They move further from the centre, because the slits are closer together.
  3. They stay where they are, because the wavelength has not changed.
Show the answer

They move further from the centre, because the slits are closer together.

More lines per mm means a smaller slit separation a. From sin theta = lambda/a, a smaller a gives a larger angle.

To measure a wavelength with a grating, measure the angle of a maximum and use λ = a sin θ/n.

The method

  1. Shine light of one wavelength, such as a laser or a sodium lamp, onto a grating at right angles. You need to know its number of lines per mm.
  2. Find the central bright maximum, order 0.
  3. Measure the angle between the two first-order maxima, one on each side, and halve it to get θ.
  4. Work out a from the lines per mm, then λ = a sin θ/n.

Measuring both sides and halving reduces the error if the grating does not quite face the light. A higher order gives a larger angle, so the same reading error is a smaller fraction of it.

Using a screen

With a screen a distance D from the grating, the first-order spot is a distance y from the centre. Then y/D is tan θ, not sin θ. Find θ first, then take its sine.

Measuring on a screen

First-order spots on a screen 1.000 m away

Screen distances give tan theta, not sin thetaThe screen is 1.000 m from the grating. The first-order spots are 0.3145 m above and below the centre. So tan theta is 0.3145 and theta is about 17.46 degrees.D = 1.000 m+0.3145 m-0.3145 m0ScreenGratingNormal incidence; equal distance scales

Find θ = tan-1(0.3145/1.000) first, then use λ = a sin θ. Measuring both spots checks that the grating faces the beam squarely.

The screen is 1.000 m from a grating with 600 lines per mm. The first-order spots are 0.3145 m either side of the centre.

Worked example

From a screen to a wavelength

The grating has 600 lines per mm, so a = 1.667 × 10-6 m. D = 1.000 m and y = 0.3145 m.

θ = tan-1(0.3145/1.000) = 17.46°
λ = a sin θ/n = 1.667 × 10-6 × sin 17.46°
= 5.00 × 10-7 m = 500 nm

Using sin θ = y/D instead would give 1.667 × 10-6 × 0.3145 = 524 nm, about 5% too big.

Check your understanding

A grating with 500 lines per mm is 1.00 m from a screen. The first-order spots are 0.30 m either side of the centre. What is the wavelength?

  1. 600 nm
  2. About 1030 nm
  3. 575 nm
Show the answer

575 nm

tan theta = 0.30/1.00, so theta = 16.7 degrees and sin theta = 0.2873. With a = 1/500 000 = 2.00 x 10-6 m, lambda = a sin theta = 2.00 x 10-6 x 0.2873 = 5.75 x 10-7 m.

A real example. A sodium lamp is a common source in school labs. NIST lists its two brightest lines at 588.995 nm and 589.592 nm, and school data round them to 589 nm. Take a 300 lines per mm grating. Then sin θ = 589 × 10-9 × 300 000 = 0.177, so the first order is at 10.2°.

Measure θ from the centre. If you measure from one first-order spot to the other, halve the angle first.