Lesson 7 of 10
Testing the circuit rules
I can state and apply the equal-current rule for a series circuit.Syllabus
Syllabus K323, 15(b). State and apply the equal-current rule for a series circuit.
I can state and apply the sum of series potential differences.Syllabus
Syllabus K323, 15(c). State and apply the sum of series potential differences.
I can state and apply the sum of parallel branch currents.Syllabus
Syllabus K323, 15(d). State and apply the sum of parallel branch currents.
I can state and apply the equal potential difference across parallel branches.Syllabus
Syllabus K323, 15(e). State and apply the equal potential difference across parallel branches.
Make a guess. You are not marked.
Two lamps are in parallel across a cell. You want to measure the total current from the cell. Where should the ammeter go?
Show the answer
In the main wire, before the current splits between the lamps.
The total current flows in the main wire, between the cell and the first junction. An ammeter there, in series, reads it.
You can test the series and parallel rules by measuring currents and p.d.s. Each reading must come from the right place in the circuit.
An ammeter goes in series in the path you measure. A voltmeter goes across the two ends of the part you measure.
Use a low-voltage cell or battery, a switch and suitable resistors. Disconnect the supply while you change the connections. Choose resistors that do not heat up much, so that their resistance stays the same.
A digital multimeter can measure current, p.d. or resistance. Set it to the right quantity and range before each reading.
Pair each p.d. reading with the right current reading
These are the readings the rules predict, not real results. The meters are ideal: the ammeter has almost no resistance and the voltmeter takes almost no current.
Measure the whole series circuit
Resistance of the whole circuit: 3.00/0.100 = 30.0 ohm. The voltmeter is across both resistors, so its 3.00 V is not the p.d. across either one.
Measure the whole parallel circuit
Resistance of the whole circuit: 3.00/0.450 = 6.67 ohm. The main ammeter reads the two branch currents added together.
For 3.00 V across each network, the rules predict these readings:
- Series: the total current is 0.100 A. The 10.0 Ω resistor has 1.00 V across it and the 20.0 Ω resistor has 2.00 V. The whole circuit's resistance is 3.00/0.100 = 30.0 Ω.
- Parallel: the currents are 0.300 A through 10.0 Ω and 0.150 A through 20.0 Ω. The total current is 0.450 A, so the whole circuit's resistance is 3.00/0.450 = 6.67 Ω.
- Choose the reading. For the total current, put the ammeter in the main wire. For one branch, put it in that branch. Put the voltmeter across the exact part or group you are testing.
- Set the range and the + terminal. Use a d.c. range bigger than the reading you expect. A battery labelled 3 V can give a little more than 3 V. Join each meter's + terminal to the side nearer the cell's + terminal.
- Record where each reading was taken. Name the part or the two points, and give units. Compare the main current with the sum of the branch currents, or the supply p.d. with the sum of the series p.d.s.
- Find a resistance from a matching pair. For one part, divide its p.d. by its current. For the whole circuit, divide the p.d. across A and C by the total current.
If you move one meter from place to place, the readings are taken at different times. The battery's p.d. can drift and the resistors can warm up in between. Check the supply, and let the readings settle.
Loose contacts add resistance. A meter can only show so many digits. Repeat readings to see how much they scatter. But fix a wrong connection or range straight away: repeating a mistake does not make it right.
Real readings will not match the rules exactly. For example, a total current of 0.448 A against 0.450 A still supports the parallel rule. The small difference comes from the meters and the contacts.
Brightness is not a current reading. A lamp's resistance changes as its filament heats up. Use an ammeter, and use fixed resistors when you test the rules.
Check your understanding
Two resistors are in series with a battery. A voltmeter reads 1.02 V across one resistor and 1.96 V across the other. Across the battery it reads 3.00 V. Which of these is the best conclusion?
Show the answer
The readings support the rule, since 2.98 V is close to 3.00 V.
1.02 + 1.96 = 2.98 V. A difference of 0.02 V is small enough to come from the meter and the contacts, so the readings fit the rule that series p.d.s add up.