K323 / 2027
D.C. circuits overview

Lesson 10 of 10

Where to put the sensor

  • I can describe NTC thermistors and LDRs and explain their use as divider input transducers.Syllabus

    Syllabus K323, 15(i). Describe NTC thermistors and LDRs and explain their use as divider input transducers.

  • I can solve simple circuits involving both NTC thermistors and LDRs.Syllabus

    Syllabus K323, 15(j). Solve simple circuits involving both NTC thermistors and LDRs.

Make a guess. You are not marked.

A street light must switch on in the dark, so its control circuit needs a p.d. that rises as it gets dark. A divider has an LDR and a fixed resistor. Across which part should this output be taken?

  1. Across the LDR, because its share of the p.d. rises in the dark.
  2. Across both parts together, because that p.d. is the largest one.
  3. Across the fixed resistor, because its resistance stays the same in the dark.
Show the answer

Across the LDR, because its share of the p.d. rises in the dark.

In the dark the LDR's resistance rises, so it takes a bigger share of the supply p.d. The p.d. across it rises.

Whether the output rises or falls depends on which arm holds the sensor, and on which part you measure across.

A sensor's resistance falls when it gets warmer or brighter, as in thermistor and LDR circuits. A part's share of the supply p.d. falls when its share of the resistance falls.

An LDR in the upper arm

Now the LDR joins A to B, and a fixed 4.0 kΩ resistor joins B to C. The output is across the fixed lower resistor. The LDR's resistance is 12.0 kΩ when it is dim and 2.0 kΩ when it is brighter.

The LDR is the upper arm

The supply is 6.0 V and the output meter takes almost no current. The output is across the fixed lower resistor, between B and C.

LDR above a fixed lower resistor

LDR above a fixed lower resistorA 6.0 V supply is across A and C. An LDR is the upper arm, from A to B. A fixed 4.0 kilohm resistor is the lower arm, from B to C. Light arrows point in towards the LDR. The ideal output voltmeter is across the fixed resistor, between B and C. When the LDR resistance falls from 12.0 to 2.0 kilohm, V_BC rises from 1.5 to 4.0 V.+-6.0 VVA: 6.0 VBC: 0 V reference+-LDRFixed4.0 kohm

Dim: LDR 12.0 kohm, output 1.5 V. Brighter: LDR 2.0 kohm, output 4.0 V. The output is across the fixed lower resistor.

The LDR is the upper arm and a fixed 4.0 kΩ resistor is the lower arm. The supply is 6.0 V, and the output is across the fixed resistor.

Light to output p.d.

Make it brighter

Dim: the total resistance is 12.0 + 4.0 = 16.0 kΩ. The current is 6.0/16 000 = 0.000375 A = 0.375 mA. Output VBC = 6.0 x 4.0/(12.0 + 4.0) = 1.5 V.

Brighter: the total resistance is 2.0 + 4.0 = 6.0 kΩ. The current is 6.0/6000 = 0.0010 A = 1.0 mA. Output VBC = 6.0 x 4.0/(2.0 + 4.0) = 4.0 V.

More light lowers the LDR's resistance, so the fixed resistor gets a bigger share of the p.d. The output rises. The LDR's own p.d. falls from 4.5 V to 2.0 V.

Try it step by step

Work it out in steps: Total resistance in ohm, then Output p.d. across the fixed resistor in V, then Output when the sensor resistance falls.

  1. Problem 1. A thermistor of resistance 8.0 kilo-ohm (cold) is the upper resistor of a divider. The lower resistor is a fixed 4.0 kilo-ohm, and the output is across it. The supply is 6.0 V. Find the output and say what happens to it when the thermistor warms.
  2. Problem 2. The same thermistor has warmed to 2.0 kilo-ohm. The fixed lower resistor is still 4.0 kilo-ohm and the supply is 6.0 V. Find the output, then say what happens if it warms further.
  3. Problem 3. An LDR of resistance 12 kilo-ohm (dark) is the upper resistor. The fixed lower resistor is 3.0 kilo-ohm, and the output is across it. The supply is 9.0 V. Find the output, then say what happens when light shines on the LDR.
Show the answer

Problem 1.

Total resistance in ohm: R = 8000 + 4000 = 12000 ohm

Output p.d. across the fixed resistor in V: V out = 6.0 x 4000 / 12000 = 2.0 V

Output when the sensor resistance falls: Warming lowers the thermistor resistance, so the fixed resistor takes a larger share of the 6.0 V: the output rises.

Problem 2.

Total resistance in ohm: R = 2000 + 4000 = 6000 ohm

Output p.d. across the fixed resistor in V: V out = 6.0 x 4000 / 6000 = 4.0 V

Output when the sensor resistance falls: Warming further lowers the thermistor resistance again, so the output rises further.

Problem 3.

Total resistance in ohm: R = 12000 + 3000 = 15000 ohm

Output p.d. across the fixed resistor in V: V out = 9.0 x 3000 / 15000 = 1.8 V (2 sf)

Output when the sensor resistance falls: Light lowers the LDR resistance, so the fixed resistor takes a larger share: the output rises.

Swap to reverse the change

Swap the sensor and the fixed resistor, or measure across the other arm, and the output changes the opposite way. So always name the part whose resistance changes, and the two points you measure across.

Street lights can use this idea. Some have an LDR, so that daylight falling on it switches the light off, which saves energy. A light that comes on in the dark needs an output that rises in the dark, such as the p.d. across the LDR.

Test a sensor circuit fairly

Keep the supply p.d. fixed, and put the voltmeter across the named output. Wait for the sensor to settle before you record a reading. For a thermistor, measure the temperature with a thermometer. The current can warm the thermistor a little, so keep it small. For an LDR, change only the light level and keep other lights the same.

The resistance values here belong to these examples. Each real sensor needs its own readings before its output can be read as a temperature or a light level.

Check which arm holds the sensor. The same LDR gives a rising output in one arm and a falling output in the other.

Check your understanding

A 6.0 V divider has an NTC thermistor as its upper arm and a fixed 3.0 kilohm resistor as its lower arm. Output is across the fixed lower resistor. Warming reduces the NTC resistance from 6.0 to 2.0 kilohm. What happens to the unloaded output?

  1. It falls from 4.0 V to 2.4 V.
  2. It stays at 2.0 V because the output resistor has not changed.
  3. It rises from 2.0 V to 3.6 V.
Show the answer

It rises from 2.0 V to 3.6 V.

Across the fixed lower arm, V_out = 6.0 x 3.0/(R_NTC + 3.0), using the same resistance units. Initially this is 2.0 V; afterwards it is 3.6 V. The falling upper resistance gives the fixed lower resistor a larger share of the supply.