9478 / 2027
Temperature and Ideal Gases overview

Lesson 5 of 8

Investigating pressure and temperature

  • I can show an understanding that a thermodynamic scale of temperature has an absolute zero and is independent of the property of any particular substance.Syllabus

    Syllabus 9478, 12(a). Show an understanding that a thermodynamic scale of temperature has an absolute zero and is independent of the property of any particular substance.

  • I can recall and use pV = NkT, where N is the number of particles.Syllabus

    Syllabus 9478, 12(c). Recall and use pV = NkT, where N is the number of particles.

Make a guess. You are not marked.

A student heats the water bath around a flask of gas, then reads the pressure at once, before the gas has warmed up. How does the reading compare with the value pV = nRT gives at the bath temperature?

  1. Higher, because the hot bath squeezes the flask.
  2. Lower, because the gas is still cooler than the bath.
  3. The same, because the pressure is set by the bath temperature.
Show the answer

Lower, because the gas is still cooler than the bath.

Pressure depends on the temperature of the gas. Until the gas reaches the bath temperature, its pressure is below the value predicted for the bath temperature.

To test p ∝ T, keep a fixed mass of gas at a fixed volume. Change its temperature in steps and measure its absolute pressure each time.

The method

Put a sealed flask of air in a water bath, with a thermometer in the water. Join the flask by a short tube to a pressure sensor. Heat the bath in steps. At each step, stir and wait until the pressure reading stops changing, then record the temperature and the pressure.

  • Check for leaks, so the amount of gas stays fixed.
  • Keep the tube short, because the gas in it is not in the bath.
  • Use the absolute pressure, not a gauge reading.

Pressure against temperature at fixed volume

The graphs use a different sample from the one above: its pressure is 100.000 kPa at 300 K.

A sealed flask in a water bath

A sealed flask of gas in a water bath, joined by a tube to a pressure sensorA sealed flask sits in a water bath with a thermometer in the water. A short tube joins the flask to a pressure sensor above the bath. The gas in the flask, the tube and the sensor is the fixed sample.AbsolutepressuresensorBaththermometerGas inconnecting tubeRigid vesselSealed gasControlled water bath

Wait until the gas has reached the bath temperature before each reading. Keep the tube short, check for leaks and measure absolute pressure.

Absolute pressure against kelvin temperature

Against kelvin, the line passes through the originPressure from 0 to 120 kPa against temperature. The four points are 100.000, 106.667, 113.333 and 120.000 kPa at 300, 320, 340 and 360 K. On the kelvin axis the line passes through the origin.010020030036004080120Absolute pressure / kPaTemperature T / K

Solid line and points: the measured range, 300 K to 360 K. Dashed line: the model extended. The gradient is 333.3 Pa/K.

The same model against Celsius temperature

Against Celsius, the same line meets zero pressure at -273.15 degreesPressure from 0 to 120 kPa against temperature. The four points are 100.000, 106.667, 113.333 and 120.000 kPa at 300, 320, 340 and 360 K. On the Celsius axis the line crosses 0 °C at 91.05 kPa and reaches zero pressure at -273.15 °C.-273.15-100086.8504080120At 0 °C:91.05 kPaAbsolute pressure / kPaCelsius temperature θ / °C

Solid line and points: the measured range, 300 K to 360 K. Dashed line: the model extended. The brown line marks 0 °C, not absolute zero. The line meets zero pressure at -273.15 °C.

These pressures come from the ideal model, rounded to 0.001 kPa. A real gas would turn to liquid before the pressure reached zero.

The apparatus, then the same results plotted against kelvin and against Celsius. This model sample has a pressure of 100.000 kPa at 300 K.
Pressures from the ideal model, at fixed volume
T / Kp / kPa
300100.000
320106.667
340113.333
360120.000

Against T in kelvin, the points lie on a straight line through the origin, with gradient 333.3 Pa/K. Against θ in °C, the same line crosses 0 °C at 91.05 kPa. The data cover only 300 K to 360 K; a real gas turns to liquid long before 0 K.

Paper 4 practice: spreadsheet

Find the gradient of p against T

Use the four pairs above. The Motion spreadsheet method shows how to enter data, copy formulas and draw a scatter graph.

  1. Put temperature / K in A1 and pressure / kPa in B1. Enter the four pairs in A2:B5 as numbers.
  2. Put pressure / Pa in C1 and enter =B2*1000 in C2. Fill it down to row 5.
  3. Make an XY scatter graph of C2:C5 against A2:A5, with axes T / K and p / Pa. Add a straight trend line and show its equation. Do not force it through zero.
  4. The gradient is (N/V)k, from p = (N/V)kT. Divide it by k = 1.38 × 10-23 J/K to find the number density N/V.
Compare your fitted line

The fit gives a gradient of 333.330 Pa/K and an intercept of +1.10 Pa, close to zero. The tiny differences from 333.333 Pa/K and zero come from rounding the data.

N/V = 333.330/(1.38 × 10-23) = 2.42 × 1025 m-3

Check your understanding

For a fixed volume of gas, a graph of absolute pressure against kelvin temperature is a straight line through the origin with gradient 345 Pa/K. With k = 1.38 x 10-23 J/K, how many molecules are there per cubic metre?

  1. 2.50 x 1025 m-3
  2. 4.76 x 10-21 m-3
  3. 41.5 m-3
Show the answer

2.50 x 1025 m-3

From p = (N/V)kT, the gradient is (N/V)k. So N/V = 345/(1.38 x 10-23) = 2.50 x 1025 m-3.

What can go wrong

  • Reading too soon: the gas is still cooler than the bath, so its pressure is lower than the model predicts at the bath temperature.
  • A leak: gas escapes, so N is no longer fixed.
  • Gauge readings: leaving out the outside pressure shifts the line down, so it no longer passes through the origin.

The thermometer shows the bath temperature, not the gas temperature. Wait for the gas to catch up before each reading.