Lesson 11 of 11
Efficiency and energy losses
I can give examples of stores and transfers and apply conservation of energy to problems.Syllabus
Syllabus 9478, 4(b). Give examples of stores and transfers and apply conservation of energy to problems.
I can explain the implications of energy losses in practical devices and calculate useful-output to total-input efficiency.Syllabus
Syllabus 9478, 4(n). Explain the implications of energy losses in practical devices and calculate useful-output to total-input efficiency.
Efficiency is the useful energy output divided by the total energy input. Real devices lose some energy, often by warming, so their efficiency is less than 100%.
Efficiency has no unit. It is often given as a percentage. You can also use useful output power / input power, if both are for the same time.
Worked efficiency
The motor that lifts a load
The motor lifts a 40.0 N load through 5.00 m in 4.00 s at steady speed. The electrical input is 320 J. The useful output is the gain in gravitational energy, 40.0 × 5.00 = 200 J.
Input power = 320 / 4.00 = 80.0 W
Efficiency = 200 / 320 = 0.625 = 62.5%
Check with P = Fv. The load rises at 5.00 / 4.00 = 1.25 m/s, so the lifting force gives 40.0 × 1.25 = 50.0 W.
Try it step by step
Work it out in steps: Useful power = mgh / t in W, then Input power = useful power / efficiency in W, then Input energy in one minute in J.
Show the answer
Problem 1.
Useful power = mgh / t in W: Useful power = 50 x 9.81 x 12 / 20 = 294 W
Input power = useful power / efficiency in W: Input power = 294 / 0.60 = 491 W
Input energy in one minute in J: Input energy = 491 x 60 = 29400 J (3 sf)
Problem 2.
Useful power = mgh / t in W: Useful power = 80 x 9.81 x 10 / 16 = 491 W
Input power = useful power / efficiency in W: Input power = 491 / 0.75 = 654 W
Input energy in one minute in J: Input energy = 654 x 60 = 39200 J (3 sf)
Problem 3.
Useful power = mgh / t in W: Useful power = 20 x 9.81 x 15 / 10 = 294 W
Input power = useful power / efficiency in W: Input power = 294 / 0.70 = 420 W
Input energy in one minute in J: Input energy = 420 x 60 = 25200 J (3 sf)
Useful lifting power and input power describe different transfers
A steady lift can transfer energy with zero resultant force
Use the lifting force to find the power, not the zero resultant force.
Same energies in half the time
Halving the time doubles both powers. The efficiency stays 62.5%.
What the losses mean
The 120 J that warms the motor and the air does not lift the load. So the motor needs more input than the 200 J it delivers. Less friction in the motor would mean less input for the same lift. The lost energy is not destroyed; it is just not useful for this task.
An efficiency alone does not tell you an amount of energy. You also need the input or the output.
Measure the efficiency of a lift
- Load: measure its weight with a force meter, or its mass and use mg.
- Height: measure the vertical rise with a metre rule. Read the scale at eye level to avoid parallax.
- Time: time the same start and finish as the height.
- Input energy: read a joulemeter at the start and the end of that same interval.
- Work out: useful energy = weight × height, then efficiency = useful energy / input energy.
A real example. NASA's Perseverance rover on Mars is powered by an MMRTG. Its plutonium fuel gives out about 2,000 W of heat at first. Thermocouples turn that into about 110 W of electrical power, so its efficiency is about 6%. NASA's fact sheet says such generators supply electricity "and useful excess heat".
Efficiency is useful output ÷ total input, so it is less than 1. If your input comes out smaller than your output, you multiplied when you should have divided.
Check your understanding
Two supplied motor runs each transfer 320 J in and raise the load-Earth gravitational store by 200 J. One run takes 4.00 s and the other 2.00 s. Which of these comparisons follows from the data?
Show the answer
The faster run has twice the input and output powers; efficiencies are both 62.5%.
Input powers are 80 and 160 W; useful output powers are 50 and 100 W. Each efficiency is 200/320 = 0.625. This comparison relies on the supplied equal energies; real efficiency need not stay constant at another operating speed.