8867 / 2027
Electromagnetism overview

Lesson 8 of 11

Current balance: a graph and its errors

  • I can explain how a current balance uses conductor force to measure magnetic flux density.Syllabus

    Syllabus 8867, 10(h). Explain how a current balance uses conductor force to measure magnetic flux density.

Make a guess. You are not marked.

A student uses the whole length of the wire for l, not just the part inside the magnet's field. How does this affect her value of B?

  1. It makes no difference, as l cancels.
  2. It is too big.
  3. It is too small.
Show the answer

It is too small.

B = F/(Il). Using a length that is too big makes the answer too small.

Take readings at several currents and plot the force against the current. The gradient is Bl, so B = gradient / l.

Keep the length, the angle and the magnet the same. Then F = BlI, so a graph of F against I is a straight line through the origin, with gradient Bl.

Readings from a model current balance, with 0.0500 m of wire in the field
I / AReading / gChange / gF / mN
0.00150.000.000
0.40150.200.201.962
0.80150.400.403.924
1.20150.600.605.886
1.60150.800.807.848

Force against current: a straight line

Force against current: a straight lineThe graph plots the upward force on the wire, in mN, against the current. The five points lie on a straight line through the origin, with gradient 4.905 mN/A.0246800.40.81.21.6Wire force upward / mNCurrent I / A

Gradient = 4.905 mN/A = 0.004905 N/A. Divide by the length, 0.0500 m: B = 0.0981 T.

The force on the wire against the current. The points lie on a straight line through the origin with gradient 4.905 mN/A.
Gradient = 7.848 / 1.60 = 4.905 mN/A
= 4.905 × 10-3 N/A
B = gradient / l = 4.905 × 10-3 / 0.0500
= 0.0981 T

Change mN/A to N/A before you divide. A real graph may not pass through the origin. Do not force the line through it; look for the cause, such as a balance reading that drifts.

Doing the experiment well

  1. Use a low-voltage supply, and switch off before you change the circuit.
  2. Measure only the length of wire inside the field, at right angles to it.
  3. Keep leads and stands clear of the magnet, and run the return wire outside the field.
  4. Record the reading with no current, and check it again later for drift.
  5. Take several currents, with repeats. Then reverse the current and repeat.

Look out for these errors. A lead that touches the magnet adds a force of its own. The field is weaker near the edges of the gap, so the length of wire in a uniform field is not sharp. Reversing the current helps you spot a fixed offset, but it does not remove every error.

Readings to 0.01 g can each be out by up to 0.005 g, so their difference can be out by 0.010 g. For a 0.60 g change, that is 0.010/0.60 = 1.7%, before any other errors.

If you use the whole wire, not just the part in the field, l is too big. Then your value of B comes out too small.

Check your understanding

In a current balance, a graph of the force on the wire against the current is a straight line with gradient 2.4 mN/A. The length of wire in the field is 0.040 m. Which of these is the magnetic flux density?

  1. 60 T
  2. 9.6 x 10-5 T
  3. 0.060 T
Show the answer

0.060 T

The gradient is Bl. In newtons it is 2.4 x 10-3 N/A, so B = 2.4 x 10-3 / 0.040 = 0.060 T.