K323 / 2027
General properties of waves overview

Lesson 6 of 10

Measuring wave speed

  • I can apply wave speed = frequency x wavelength in new situations.Syllabus

    Syllabus K323, 10(d). Apply wave speed = frequency x wavelength in new situations.

Make a guess. You are not marked.

The dipper of a ripple tank vibrates about 4 times each second. A student has a hand-held stopwatch. Which method gives the best value for the period?

  1. Time one vibration three times and take the mean.
  2. Time one vibration as carefully as possible.
  3. Time 20 complete vibrations, then divide the time by 20.
Show the answer

Time 20 complete vibrations, then divide the time by 20.

One vibration lasts about 0.25 s, which is close to human reaction time. Over 20 vibrations, about 5 s, the same reaction time is a much smaller fraction of the reading.

To measure wave speed, find the wavelength from the crest spacing and the frequency from timing. Then use v = fλ.

This lesson applies v = fλ to readings from a ripple tank.

Measure several wavelengths

Set up a steady pattern in a ripple tank. Keep the water depth the same throughout. Measure across several crests in a top view that has a known scale. The readings below are model values.

Six crests enclose five wavelengths

A supplied calibrated span is 40.0 cm from crest 1 to crest 6. Use that reading, not the displayed size of the picture.

A forty-centimetre span across six crests contains five wavelengthsSix equally spaced straight crests are numbered one to six in a top view. Each of the five intervening gaps is labelled lambda for one wavelength. A total bracket from the first crest to the sixth is labelled 40.0 centimetres. Therefore one wavelength is 8.00 centimetres, or 0.0800 metres. These are supplied model readings, not a screen ruler measurement.Top view of six crests123456λλλλλ40.0 cm
The span from the first to the sixth crest contains five wavelengths. Its stated length is 40.0 cm. Use the given scale, not the size of the diagram on the screen.

One wavelength is 40.0/5 = 8.00 cm = 0.0800 m. Six crests have five gaps between them, so divide by five, not six.

Time many complete oscillations

Repeated times for 20 complete source oscillations
TrialTime / s
14.90
25.00
35.10

The mean time is (4.90 + 5.00 + 5.10)/3 = 5.00 s. Start and stop the count at the same stage of the dipper's motion.

f = 20/5.00 = 4.00 Hz
T = 5.00/20 = 0.250 s
v = 4.00 x 0.0800 = 0.320 m/s
The 5.00 s is the time for 20 oscillations. It is not the time for one crest to travel from the first position to the sixth.

Match each improvement to its cause

  • Crest positions are hard to judge: measure a longer span with several wavelengths and divide by the number of gaps. The same reading error is then a smaller fraction of the span.
  • Reaction time in starting and stopping: time many complete cycles. The reaction time is then a smaller fraction of the total time.
  • Wrong length scale: the image on the screen may be larger than the real water surface. Place a ruler in the tank to set the scale, and read it without parallax.
  • Unclear pattern: keep the dipper steady and the water depth the same. Avoid a region where reflected waves overlap the pattern.

Repeating shows how much the readings vary. It does not fix counting six gaps instead of five or using a wrong scale. It also does not help if the water depth changes between the two measurements.

Another method follows the same pulse between two marked positions and uses distance divided by travel time. That travel time is not the period. Be clear about which event starts the timing and which stops it.

Keep the spacing and the timing apart. First find one wavelength. Next find the number of cycles each second. Only then use v = fλ.

Check your understanding

The span from the first to the sixth crest is 40.0 cm. The source completes 20 oscillations in a mean time of 5.00 s. What is the wave speed for these readings?

  1. 0.320 m/s, using five wavelengths and frequency 4.00 Hz.
  2. 0.267 m/s, using six wavelengths in the span.
  3. 1.60 m/s, using 40.0 cm as one wavelength.
Show the answer

0.320 m/s, using five wavelengths and frequency 4.00 Hz.

Wavelength = 0.400/5 = 0.0800 m. Frequency = 20/5.00 = 4.00 Hz. Therefore v = f lambda = 4.00 x 0.0800 = 0.320 m/s. The 5.00 s interval times source oscillations, not one crest travelling across the measured span.

Practise an exam question

Write your answer first, then tick the mark points it makes.

Exam-style question

In a ripple tank, 10 complete waves pass a point in 4.0 s. The distance between neighbouring crests is 1.6 cm. Calculate the frequency and the speed of the waves. [3]

Saved on this browser only. Anyone using this browser can see it.