Lesson 6 of 12
Normalising a sine-shaped wavefunction
I can represent a particle state by a wavefunction, interpret amplitude squared as probability density, including an atomic electron cloud, and normalise square and sinusoidal profiles.Syllabus
Syllabus 9478, 19(f). Represent a particle state by a wavefunction, interpret amplitude squared as probability density, including an atomic electron cloud, and normalise square and sinusoidal profiles.
Make a guess. You are not marked.
A particle has the wavefunction psi = C sin(pi x/L) in a box from 0 to L. Compare the chance of finding it in the middle half of the box with the chance of finding it in the two outer quarters together.
Show the answer
The middle half is much more likely.
The density sin2 is largest in the middle and zero at the walls. The middle half holds about 0.82 of the probability, the outer quarters about 0.18.
For ψ = C sin(πx/L) between 0 and L, the average of sin2 is ½. So the total area is C2L/2, and normalisation gives C = √(2/L).
The density is C2sin2(πx/L). Over a whole half-wave, sin2 spends as much time near 1 as near 0, so its average is ½. The area under the density is its average height times the width:
C = √(2/L)
Worked sine normalisation
A sine wavefunction 4.00 nm wide
|ψ|2 = 0.500 sin2(πx/4.00) nm-1, with x in nm
The density is highest in the middle, at 2.00 nm, and zero at the ends. By symmetry, each half has probability 0.500. The middle half, from 1.00 to 3.00 nm, has probability about 0.82, so the outer quarters together have only about 0.18.
The coefficient is different from the square shape. Using 1/√L here would give a total probability of only ½.
Sinusoidal profile: signed amplitude
The coefficient is √(2/L) = 0.707 nm^-1/2, so the whole density area is 1.
Sinusoidal profile: density and interval probability
The shaded area under the density is the probability, 0.818. The whole area is 1.
Paper 4 practice: spreadsheet
Estimate an area with trapezia
Download the starter workbook. Its Coarse, Fine and Finer sheets list x in nm with steps of 0.5, 0.25 and 0.125 nm. They are made from the formula, not measured. G2 holds L = 4.
| Cell | Formula |
|---|---|
| H2: C | =SQRT(2/$G$2) |
| B2: ψ | =$H$2*SIN(PI()*A2/$G$2) |
| C2: density | =B2^2 |
| D2: strip area | =(A3-A2)*(C2+C3)/2 |
Fill B and C to the last row of x values. Fill D to one row before the last, because each strip needs a next point. On the Coarse sheet, x is in A2:A10, so D goes to D9. Add up D2:D9 for the whole width, and D4:D7 for 1 to 3 nm. On the Fine sheet use D2:D17 and D6:D13, and on the Finer sheet D2:D33 and D10:D25.
Compare your results
The 1 to 3 nm estimates are 0.80178, 0.81421 and 0.81729. The exact value is ½ + 1/π = 0.81831. Smaller steps give a better estimate. The whole-width sums all come to 1.
Do not use the square-profile result C = 1/√L for a sine shape. The sine shape needs √(2/L), because the average of sin2 is only ½.
Check your understanding
For 0 < x < L, psi = C sin(pi x/L), with L = 4.00 nm and zero amplitude outside. The mean of sin2 over this interval is 1/2. Which positive C normalises the state?
Show the answer
0.707 nm^(-1/2).
C2 L/2 = 1 gives C = sqrt(2/L). With L entered in nm, C = sqrt(2/4.00) = 0.707 nm^(-1/2), and density times a width in nm is dimensionless.