9478 / 2027
Oscillations overview

Lesson 5 of 9

Investigating an oscillator

  • I can investigate an oscillator using calibrated measurements and graphical methods.Syllabus

    Syllabus 9478, 9(b). Investigate an oscillator using calibrated measurements and graphical methods.

To test for SHM, record position against time, work out the acceleration, and plot a against x.

Taking the measurements

  1. Find equilibrium. Let the system settle and mark its rest reading. Subtract this from each position to get the displacement x.
  2. Release it the same way each time. Pull it aside and let go without a push.
  3. Time many complete cycles. Start and stop as it passes the same point, moving the same way. Repeat, then divide by the number of cycles.
  4. Record position against time. Use a motion sensor or a video with a ruler in the plane of motion. View it square on, so the scale is not distorted.
  5. Check the model. See whether the amplitude or period changes from cycle to cycle.

From positions to velocity and acceleration

These positions come from the model x = 0.0500 sin(4.00t), rounded to 0.00001 m. They show the method; they are not real readings.

Model positions every 0.10 s
Time t / sDisplacement x / m
0.000.00000
0.100.01947
0.200.03587
0.300.04660
0.400.04998

For each interval, Δx/Δt gives an average velocity. Plot it at the middle of the interval. The four values are 0.1947, 0.1640, 0.1073 and 0.0338 m/s, at 0.05, 0.15, 0.25 and 0.35 s.

For example, from 0.10 to 0.20 s: (0.03587 - 0.01947)/0.10 = 0.1640 m/s. Do the same with the velocities to estimate the acceleration:

a at 0.20 s ≈ (0.1073 - 0.1640)/(0.25 - 0.15)
= -0.567 m/s2

The model gives -16.0 × 0.03587 = -0.574 m/s2 at that time. The estimate is close but not exact, because it averages over 0.10 s.

Check your understanding

Positions of a cart are recorded every 0.10 s. The average velocity between t = 0.20 s and t = 0.30 s is found from the change in x divided by 0.10 s. At which time should this velocity be plotted?

  1. 0.20 s, at the start of the interval, where the change in x began.
  2. 0.30 s, the end of the interval, when the reading was finished.
  3. 0.25 s, the middle of the time interval it was measured over.
Show the answer

0.25 s, the middle of the time interval it was measured over.

An average velocity over an interval best matches the velocity at its midpoint. Plotting it at either end shifts the whole velocity graph in time.

Testing for SHM

With a real record, find a and x at the same times, on both sides of equilibrium. Plot a against x. A straight line through the origin with a negative gradient supports SHM. Its gradient is -ω2. Take the square root of its size to get ω, and compare that with 2π/T from the timing.

Shorter intervals follow the motion more closely, but the changes in x become small compared with the reading errors. Working out a rate makes errors bigger, and a rate of a rate makes them bigger again. So pick intervals that still give clear changes.

Check your understanding

A student plots acceleration against position for an oscillating cart. The points lie on a straight line with a negative gradient, but the line crosses a = 0 at x = 2.0 cm, not at x = 0. Which of these is the most likely reason?

  1. The motion cannot be SHM, so the student should discard these readings.
  2. The readings were taken too far apart in time.
  3. Positions were read from the ruler zero instead of from equilibrium.
Show the answer

Positions were read from the ruler zero instead of from equilibrium.

In SHM, a is zero at equilibrium. Here a = 0 at 2.0 cm on the scale, so equilibrium is there. Subtract 2.0 cm from each position to get the displacement.

Measure displacement from equilibrium, not from the end of the ruler. Otherwise the a-x line will not pass through the origin.