Lesson 2 of 9
Drift velocity
I can explain current as the rate of charge flow and use I = Q/t.Syllabus
Syllabus 9478, 15(a). Explain current as the rate of charge flow and use I = Q/t.
I can derive and apply I = nAvq for a current-carrying conductor, with carrier number density and drift velocity defined.Syllabus
Syllabus 9478, 15(b). Derive and apply I = nAvq for a current-carrying conductor, with carrier number density and drift velocity defined.
The current in a wire is I = nAvq. A metal wire holds a huge number of free electrons. So even a slow drift, a fraction of a millimetre per second, gives a current of amperes.
Count the carriers that cross a section
Take a wire of cross-sectional area A. It has n free charge carriers in each cubic metre: n is the number density, in m-3. Each carrier has charge q, and they drift along the wire with mean speed v, the drift velocity.
Count charge crossing one section
Electrons fill the whole wire. The shaded slice is a way of counting them, not a packet moving through an empty wire.
With n = 8.00 × 1028 m-3, the slice holds 8.00 × 1019 electrons: 12.8 C in 5.00 s, so I = 2.56 A.
Irregular motion and net drift are different
Arrow lengths do not compare drift speed with current. The circuit responds quickly, even though each electron drifts slowly.
In time Δt, each carrier drifts a distance vΔt. So the carriers that cross the plane fill a volume AvΔt. That volume holds nAvΔt carriers, with total charge:
I = Q/Δt = nAvq
Here q is the size of the carrier's charge, e for an electron. Check the units: m-3 × m2 × m/s × C = C/s = A.
Worked carrier model
Slow drift, sizeable current
Use n = 8.00 × 1028 m-3, A = 1.00 mm2 = 1.00 × 10-6 m2, v = 2.00 × 10-4 m/s and q = 1.60 × 10-19 C.
× (2.00 × 10-4)(1.60 × 10-19)
= 2.56 A
Check it by counting. In 5.00 s, each electron drifts only vt = 1.00 mm. The slice holds nAvt = 8.00 × 1019 electrons, which carry 12.8 C. And 12.8/5.00 = 2.56 A.
A wire with half the area, carrying the same current, needs twice the drift speed: 4.00 × 10-4 m/s.
Try it step by step
Work it out in steps: Cross-sectional area A in mm2, then Drift velocity v = I / (n A e) in mm/s.
Show the answer
Problem 1.
Cross-sectional area A in mm2: A = pi x 1.02 / 4 = 0.785 mm2 = 7.85 x 10-7 m2
Drift velocity v = I / (n A e) in mm/s: v = 2.0 / (8.5 x 1028 x 7.85 x 10-7 x 1.6 x 10-19) = 1.87 x 10-4 m/s = 0.187 mm/s (3 sf)
Problem 2.
Cross-sectional area A in mm2: A = 2.0 mm2 = 2.0 x 10-6 m2
Drift velocity v = I / (n A e) in mm/s: v = 5.0 / (8.5 x 1028 x 2.0 x 10-6 x 1.6 x 10-19) = 1.84 x 10-4 m/s = 0.184 mm/s (3 sf)
Problem 3.
Cross-sectional area A in mm2: A = pi x 0.502 / 4 = 0.196 mm2 = 1.96 x 10-7 m2
Drift velocity v = I / (n A e) in mm/s: v = 1.0 / (8.5 x 1028 x 1.96 x 10-7 x 1.6 x 10-19) = 3.75 x 10-4 m/s = 0.375 mm/s (3 sf)
Why a lamp lights at once
Electrons fill the whole circuit before you close the switch. When you close it, they all start to drift almost at once, so the lamp responds quickly. No electron needs to travel from the cell to the lamp first.
A real example. HyperPhysics, at Georgia State University, works out drift speeds for copper wire and notes that the drift is very slow. It explains that the change, or "signal", travels along the wire at nearly the speed of light.
Change mm2 to m2 before using I = nAvq: 1 mm2 = 1 × 10-6 m2, not 10-3 m2. For a diameter, find the area with πd2/4 first.
Check your understanding
A wire carries a fixed current with drift-speed magnitude 2.00 x 10-4 m/s. A second wire has half the cross-sectional area, with the same current, carrier density and carrier-charge magnitude. What is its drift speed?
Show the answer
4.00 x 10-4 m/s
v = I/(nAq), so halving A doubles v when the other stated quantities remain fixed. This is a fixed-current comparison, not a claim about connecting any thinner wire to the same voltage.