Lesson 10 of 10
From resultant force to motion
I can use position or displacement gradients, and velocity gradients and areas, including non-uniform acceleration.Syllabus
Syllabus 8867, 3(c). Use position or displacement gradients, and velocity gradients and areas, including non-uniform acceleration.
I can recall and use resultant force F = ma for a body of constant mass.Syllabus
Syllabus 8867, 3(i). Recall and use resultant force F = ma for a body of constant mass.
Make a guess. You are not marked.
A constant resultant force acts on a trolley for 3.0 s. What changes by the same amount in each second?
Show the answer
The trolley's momentum, by an amount equal to the force each second.
Newton's second law: F = rate of change of momentum. A constant force changes the momentum by F newton seconds in each second.
Draw the forces first. For a body of constant mass, the resultant force sets its acceleration: F = ma.
Momentum is p = mv. When m is constant, dp/dt = m dv/dt = ma. Put that into the second law:
Fresultant = ma
Use the resultant force along your chosen direction, not just one of the forces. The acceleration points along the resultant force, which need not be the way the body is moving.
A real example. NASA gives the Saturn V moon rocket a mass of 2.8 million kg at lift-off and a thrust of 34.5 million N. Its weight was 2.8 × 106 × 9.81 = 27.5 million N. So the resultant force was 34.5 - 27.5 = 7.0 million N upwards. Then a = 7.0 × 106 / 2.8 × 106 = 2.5 m/s2.
A cart pulled along a level track
A 0.80 kg cart is moving right at +0.40 m/s. A string pulls it right with 0.60 N, and track resistance pulls it left with 0.20 N. These forces stay the same for 2.0 s, and the cart keeps moving right.
Find the resultant from the actual forces on the cart
Scale note: the horizontal arrows share one scale, and the two vertical arrows share another. Horizontally, 0.60 - 0.20 = +0.40 N. Vertically, support and weight balance. These are the four interactions; the resultant is their sum.
Worked force to motion
Find the resultant, then the motion
- Forces: the string, track resistance, the track's support and the weight. With g = 9.81 m/s2, weight and support are each 0.80 × 9.81 = 7.848 N, about 7.85 N.
- Across: Fx = +0.60 - 0.20 = +0.40 N. The vertical forces balance.
- Acceleration: a = 0.40/0.80 = +0.50 m/s2. A constant resultant and constant mass give constant acceleration.
- Motion after 2.0 s: v = 0.40 + 0.50 × 2.0 = +1.40 m/s. s = 0.40 × 2.0 + ½ × 0.50 × 2.02 = +1.80 m.
- Check with momentum: Δp = 0.80 × (1.40 - 0.40) = +0.80 kg m/s. Divided by 2.0 s, that is +0.40 N, the same resultant.
Do not put the 0.60 N pull alone into F = ma. That gives 0.75 m/s2, too large. Use the resultant, 0.40 N.
Resistance points left because the cart moves right. If the cart turned back, resistance would turn too. If the string went slack, find the new resultant first.
Check your understanding
A 0.80 kg cart is moving right when its pulling string goes slack. Track resistance remains 0.20 N leftward. What is its acceleration immediately afterwards, taking right as positive?
Show the answer
-0.25 m/s2: the cart is initially slowing while moving right.
The resultant is -0.20 N, so a = -0.20/0.80 = -0.25 m/s2. This acceleration is opposite to its present rightward velocity.
Method: video analysis and a spreadsheet (optional)
Find the motion from position data
One way is to film the cart beside a ruler in the same plane as its motion. Keep the camera square to that plane, note the time between frames and track the same point on the cart. A motion sensor is another way.
A ruler that is nearer or further than the cart makes every distance wrong by the same factor. Repeating the run does not fix that. Leave enough track for the cart to finish safely.
The numbers below are rounded values from the model for this cart, starting at +0.200 m. They are for practice, not real readings.
| Time / s | Position / m |
|---|---|
| 0.000 | 0.200 |
| 0.500 | 0.463 |
| 1.000 | 0.850 |
| 1.500 | 1.363 |
| 2.000 | 2.000 |
For each pair of neighbouring rows, divide the change in position by the change in time. The first gives (0.463 - 0.200)/(0.500 - 0.000) = 0.526 m/s. That is the average velocity over the interval.
With constant acceleration, that average equals the velocity at the middle time of the interval: (0.000 + 0.500)/2 = 0.250 s. This is exact only for constant acceleration.
Plot these velocities against their middle times and fit a straight line. Its gradient is the acceleration and its intercept is the starting velocity. Then compare mass × acceleration with the resultant 0.40 N, not the string pull alone.
Very short intervals let small reading errors swamp the change in position. A zero error in position cancels in each difference; a scale error does not.
Do not plot an interval's average velocity at its end time. And x against t2 is not a straight line here, because the cart did not start from rest.
Check the cart velocities and the fitted line
The four middle times are 0.250, 0.750, 1.250 and 1.750 s. Their average velocities are 0.526, 0.774, 1.026 and 1.274 m/s.
A straight-line fit gives gradient 0.4992 m/s2 and intercept 0.4008 m/s, so about a = 0.50 m/s2 and u = 0.40 m/s.
Resultant force = 0.80 × 0.4992 = 0.39936 N, about 0.40 N. The small difference comes from the rounded positions. More spreadsheet digits do not make a real camera measurement more precise.
Check your understanding
In a constant-acceleration cart model, x changes from 0.200 m at 0.000 s to 0.463 m at 0.500 s. The interval-average velocity is 0.526 m/s. At what representative time should it be plotted?
Show the answer
0.250 s, the midpoint of the interval.
For constant acceleration, velocity varies linearly, so its interval average represents the midpoint velocity. Rounded position data can still cause small numerical deviations from the ideal model.