8867 / 2027
Circuits overview

Lesson 2 of 10

Resistance and resistivity

  • I can define resistance as component p.d. divided by its current, and use V = IR.Syllabus

    Syllabus 8867, 9(c). Define resistance as component p.d. divided by its current, and use V = IR.

  • I can recall and use R = rho l/A for a uniform conductor under stated conditions.Syllabus

    Syllabus 8867, 9(d). Recall and use R = rho l/A for a uniform conductor under stated conditions.

The resistance of a component is the p.d. across it divided by the current in it, R = V/I. For a uniform wire, R = ρl/A, where ρ is the resistivity of the material.

R = V/I, or V = IR
1 Ω = 1 V/A

V = IR does not mean R is constant. An ohmic component has a current proportional to the p.d., at constant temperature. Then its I-V graph is a straight line through the origin.

Resistivity

A uniform wire of length l and cross-sectional area A has resistance:

R = ρl/A
A = πd2/4 for a round wire of diameter d

Resistivity ρ belongs to the material, at a given temperature. Its unit is the ohm metre, Ω m. A longer wire has more resistance; a thicker one has less. A is the area of the cut end, not the outside surface.

Worked wire

Use the wire's own readings

A wire has l = 0.800 m and d = 0.400 mm. A voltmeter across the wire reads 0.400 V, and the current is 0.125 A. A 6.0 V supply drives the circuit, through a variable resistor that takes the rest of the p.d.

Use the wire readings, not the source reading

Use the wire readings, not the source readingA complete low-voltage circuit contains the six-volt source, a 44.8-ohm series control, an ammeter and the chosen wire.+-AV44.8 Ω5.60 V0.125 A0.400 VPQ+-6.00 Vat sourceP/Q length: 0.800 mThe voltmeter spans only the wire.

The control and wire share 0.125 A. The wire has 0.400 V across P/Q; using the source's 6.00 V would include the control resistance.

Double length and diameter at fixed resistivity

Double length and diameter at fixed resistivityThe two side views use one length scale: 120 and 240 drawing units correspond to 0.800 and 1.60 metres.0.800 m1.60 md = 0.400 mmd = 0.800 mmEnd faces enlarged togetherArea AArea 4A

Length and diameter use different display scales, each shared by both wires. Length doubles but area quadruples; at unchanged resistivity the resistance is 1.60 ohm, half the original 3.20 ohm.

Resistance falls as the reciprocal of area

Resistance falls as the reciprocal of areaThe positive horizontal variable is area divided by the original area A0.0.5123400.511.52Resistance ratio R/R0Area ratio A/A0

Doubling area halves resistance. Doubling diameter is different: it gives four times the area and one quarter of the resistance if length stays fixed.

The voltmeter is across the wire only. Doubling the length and the diameter halves the resistance. R falls as the area grows.
R = 0.400/0.125 = 3.20 Ω
A = π(0.400 × 10-3)2/4 = 1.2566 × 10-7 m2
ρ = RA/l = (3.20)(1.2566 × 10-7)/0.800
= 5.03 × 10-7 Ω m

Change the diameter to metres before squaring. Using 6.0/0.125 = 48 Ω would give the resistance of the whole circuit, not the wire.

A wire of the same material with twice the length and twice the diameter has four times the area, so Rnew = 3.20 × 2/4 = 1.60 Ω.

Try it step by step

Work it out in steps: Cross-sectional area A = pi d2 / 4 in mm2, then Resistance R = rho L / A in ohm.

  1. Problem 1. A copper wire (resistivity 1.7 x 10-8 ohm m) is 50 m long and 1.0 mm in diameter. Find its resistance.
  2. Problem 2. A nichrome heating wire (resistivity 1.1 x 10-6 ohm m) is 2.0 m long and 0.50 mm in diameter. Find its resistance.
  3. Problem 3. A copper cable (resistivity 1.7 x 10-8 ohm m) is 100 m long and 2.0 mm in diameter. Find its resistance.
Show the answer

Problem 1.

Cross-sectional area A = pi d2 / 4 in mm2: A = pi x 1.02 / 4 = 0.785 mm2 = 7.85 x 10-7 m2

Resistance R = rho L / A in ohm: R = 1.7 x 10-8 x 50 / (7.85 x 10-7) = 1.08 ohm (3 sf)

Problem 2.

Cross-sectional area A = pi d2 / 4 in mm2: A = pi x 0.502 / 4 = 0.196 mm2 = 1.96 x 10-7 m2

Resistance R = rho L / A in ohm: R = 1.1 x 10-6 x 2.0 / (1.96 x 10-7) = 11.2 ohm (3 sf)

Problem 3.

Cross-sectional area A = pi d2 / 4 in mm2: A = pi x 2.02 / 4 = 3.14 mm2 = 3.14 x 10-6 m2

Resistance R = rho L / A in ohm: R = 1.7 x 10-8 x 100 / (3.14 x 10-6) = 0.541 ohm (3 sf)

A real example. HyperPhysics, at Georgia State University, lists resistivities at 20 °C. Copper is 1.68 × 10-8 Ω m; nichrome is 100 × 10-8 Ω m. So 1.0 m of 1.0 mm diameter copper wire has R = 0.021 Ω, while the same nichrome wire has 1.27 Ω, about 60 times as much. That is why heating elements use nichrome.

Use A = πd2/4, or πr2. Using πd2 makes the area four times too large, so the resistance comes out four times too small.

Check your understanding

A uniform wire has resistance 3.20 ohm. A second wire of the same material at the same temperature has twice the length and twice the diameter. What is its resistance?

  1. 1.60 ohm
  2. 6.40 ohm
  3. 3.20 ohm
Show the answer

1.60 ohm

The length factor is 2 and the area factor is 22 = 4. At unchanged resistivity, R_new/R_old = 2/4 = 1/2.