K223 / K224 / 2027
Thermal processes overview

Full chapter

Thermal processes

All 6 topics and the revision summary on one page.

01

Heating and thermal equilibrium

In short

  • Energy moves by heating from the hotter object to the cooler one.
  • At thermal equilibrium both objects have the same temperature, so there is no net transfer.

Make a guess. You are not marked.

A can of drink at 5 degrees C is left on a table in a room at 30 degrees C for a whole day. What is its temperature at the end of the day?

  1. About 17 degrees C, halfway between the two.
  2. Above 30 degrees C, because it gains energy all day.
  3. 30 degrees C, the same as the room.
Show the answer

30 degrees C, the same as the room.

Energy transfers from the warmer room to the cooler can until the two are at the same temperature. Then there is no net transfer, so the can stays at 30 degrees C.

Energy transfers by heating from a hotter region to a cooler one, until both are at the same temperature.

Heating is an energy transfer, measured in joules. Temperature relates to the average random kinetic energy of the particles. Heat and cold are not substances stored inside objects.

Thermal equilibrium: equal temperatures

Place a metal block at 60°C in thermal contact with another at 20°C. Energy transfers by heating from the hotter block to the cooler one. If the pair is cut off from the surroundings, their temperatures move towards the same value.

At thermal equilibrium, the two regions have the same temperature and there is no net energy transfer by heating between them. Their particles keep moving and acting on one another. Equilibrium does not mean that particles stop.

More detail (optional)

The starting temperatures alone do not fix the final temperature. The amounts and materials also matter, so do not assume it is the average of 60°C and 20°C. Equal final temperatures also do not mean equal total internal energies.

A thermometer relies on this. Its bulb exchanges energy with the sample until both are at the same temperature. Only then does the reading belong to the sample, which is why you wait for it to settle.

Cold does not flow. A cold drink warms up because energy enters it from the warmer room, not because "coldness" leaks out. Write the direction as energy moving from the hotter region to the cooler one.

Check your understanding

A metal block at 80 degrees C is pressed against an identical block at 20 degrees C inside an insulated box. Later both read 50 degrees C and the readings stay there. Which of these describes the blocks now?

  1. Their particles have stopped moving, because nothing is changing.
  2. Energy still flows from the first block to the second, because it started hotter.
  3. No net energy transfers between them, although their particles still move.
Show the answer

No net energy transfers between them, although their particles still move.

The blocks are in thermal equilibrium: equal temperatures, so no net transfer by heating. Their particles keep vibrating and still exchange energy, but equally in both directions.

Next, conduction explains how this energy travels through a solid.

02

Conduction

In short

  • In a solid, hotter particles vibrate more and pass energy to their neighbours. This is conduction.
  • Metals conduct best because their free electrons carry energy too.
  • An insulator slows conduction. It does not stop it.

Make a guess. You are not marked.

A metal spoon and a wooden spoon have been in the same room all day. You touch each one. Which feels colder, and why?

  1. Neither. They are at the same temperature, so they feel the same.
  2. The metal, because metal is at a lower temperature.
  3. The metal, because it conducts energy away from your hand faster.
Show the answer

The metal, because it conducts energy away from your hand faster.

Both spoons are at room temperature. Metal is a much better thermal conductor, so energy leaves your warmer hand quickly, and that fast loss feels cold.

Conduction transfers energy through a material as neighbouring particles act on one another. Metals conduct well because their mobile electrons carry energy too.

Net heating transfers energy from a hotter region to a cooler one. Temperature relates to the average random kinetic energy of the particles.

How a solid conducts

Particles at the hotter end of a solid vibrate with greater average kinetic energy. They act on their neighbours and pass energy on. In this way energy is transferred along the solid towards the cooler region.

More detail (optional)

The atoms or molecules stay near their usual positions while they vibrate. The solid does not conduct by sending its hot particles in a stream from one end to the other.

In a metal, mobile electrons give a second way to transfer energy. Electrons move through the metal and exchange energy with its particles and with other electrons. They move in both directions, but the net transfer is from the hotter region towards the cooler one.

Energy passes through the solid towards the cooler region

The large circles mark fixed mean positions. Particles at both ends vibrate; the solid does not flow along the strip.

Vibrations in a solid

Vibrations in a solid: net energy transfer from the hotter left end to the cooler right endA solid strip has its hotter end on the left and its cooler end on the right. Large particles occupy fixed mean positions in two rows. Blue double-ended arrows indicate vibration about those positions. The larger indicators at the hotter end are qualitative. Neighbouring particles interact and transfer energy; neither end has stationary particles. A separate orange arrow below the strip points right and represents net energy transfer, not the path of a particle. The models and arrow sizes are schematic.Hotter endCooler endNet energy transfer

Blue double arrows: vibration about fixed positions. Neighbouring particles transfer energy through their interactions.

An additional mechanism in a metal

An additional mechanism in a metal: net energy transfer from the hotter left end to the cooler right endA solid strip has its hotter end on the left and its cooler end on the right. Large particles occupy fixed mean positions in two rows. Small blue dots represent mobile electrons in a metal. Their blue motion arrows point in varied directions, including towards both ends. Electrons transfer energy through interactions. The large metal particles also vibrate, although their vibration indicators are omitted in this panel. The diagram does not show a one-way electric current. A separate orange arrow below the strip points right and represents net energy transfer, not the path of a particle. The models and arrow sizes are schematic.Hotter endCooler endNet energy transfer

Small blue dots and arrows: mobile electrons and their motion. They provide an additional way to transfer energy through a metal.

The orange arrows show the direction of net energy transfer. Their lengths do not measure transfer rates.

The solid particles vibrate near fixed positions, including at the cooler end. Mobile electrons add another way to transfer energy in the metal. The direction of net energy transfer is not the same as the motion of any one particle or electron.

Conductors and insulators have different rates

For samples of the same size with the same temperature difference, a good thermal conductor transfers energy more readily than a thermal insulator. An insulator slows conduction. It does not make all energy transfer impossible.

A metal pan base helps transfer energy from a hotter hob to the cooler contents. A suitable insulating handle slows conduction towards a hand. The useful material depends on whether the design should help a transfer or reduce it.

Worked explanation

Metal and wood at the same room temperature

A metal block and a wooden block have both reached 20°C in a room. A hand is warmer than either block.

  1. Direction: energy leaves the warmer hand and enters the cooler block in both cases.
  2. Rate: the metal conducts energy away from the contact region more readily than the wood.
  3. Observation: the hand cools faster in contact with the metal, so the metal can feel colder even though both blocks started at the same temperature.

The feeling depends on the rate at which the hand loses energy. It is not evidence that the metal began at a lower temperature.

Name the net transfer and how it happens. In solid conduction, particles act on their neighbours and transfer energy without bulk flow of the solid. In metals, include mobile electrons as well as vibrating particles.

Check your understanding

A metal block and a wooden block have both been in a 20 degrees C room long enough to reach that temperature. A warmer hand touches each. Why can the metal feel colder?

  1. The metal transfers a substance called cold into the hand.
  2. The metal must have started below 20 degrees C, because it feels colder to touch.
  3. Energy leaves the hand more rapidly through the better-conducting metal.
Show the answer

Energy leaves the hand more rapidly through the better-conducting metal.

The metal conducts energy away from the contact region more readily, so the hand cools faster. The direction of net heating is from the warmer hand to the cooler block in both cases.

03

Convection in fluids

In short

  • A liquid or gas warmed from below expands, becomes less dense and rises. Cooler, denser fluid sinks to take its place.
  • This circulation is a convection current. It carries energy with the moving fluid.
  • Solids cannot convect because their particles cannot flow.

Convection transfers energy with the bulk movement of a liquid or gas. Natural convection develops when density differences set the fluid in motion.

A fluid can flow. Density is mass divided by volume. If a portion of fluid expands while its mass stays the same, its density decreases. Energy still transfers overall from hotter regions to cooler ones.

Follow a complete circulation

Heat a liquid locally near one side of the bottom of a vessel. Assume that the liquid expands when warmed over the temperature range used.

  1. Warming: the portion near the heater gains energy and expands.
  2. Density change: its mass is spread over a larger volume, so it becomes less dense than the surrounding cooler liquid.
  3. Rising: the surrounding denser fluid displaces the warmer, less dense portion upwards.
  4. Return flow: cooler liquid moves into the region left behind. The moving fluid carries energy and a circulation develops.

Heating one lower region can set up a circulation

This liquid expands when warmed over the temperature range shown. Blue arrows show bulk liquid motion; the orange arrow shows energy entering from the heater.

A complete convection loop above a heater at the lower leftA container holds one continuous body of liquid. A local heater transfers energy into the lower-left region. The warmer liquid expands and becomes less dense than the cooler surrounding liquid, which displaces it upwards. Blue arrows run upwards at the left, across the top, downwards at the cooler right and back along the bottom, making one connected circulation. The blue arrows represent fluid motion that transports energy. The orange arrow from the heater represents energy transfer into the liquid. The coloured regions and arrows are qualitative.Warmer liquidLower densityCooler liquidHigher densityMovingliquidLocal heater

The returning cooler liquid completes the circulation. Energy is carried with the moving liquid.

Warmer, less dense liquid rises near the heated side. Cooler, denser liquid returns towards the lower region, completing a circulation. The arrows represent fluid motion, not a separate substance called heat.
More detail (optional)

The warmed portion does not have to lose mass or become weightless. Its smaller density follows from greater volume for the same mass. A complete explanation connects the temperature change to expansion, density and movement.

Why the heater position matters

Worked comparison

Heating water at the bottom or at the top

Consider water initially at 20°C and warming through a range in which it expands.

  • Heating near the bottom: the newly warmed, less dense water is below denser water, so it rises and promotes circulation through the sample.
  • Heating near the top: the warmed, less dense water is already above the cooler, denser water. Much less natural circulation develops through the whole sample.

Lower regions can still gain energy through other transfers. The top-heating case does not show that energy can never travel downwards.

Put these in order

A heater sits near the floor of a room. Put the explanation of how it warms the whole room by convection in order.

Show the answer

1. Air next to the heater is warmed and expands. When the same mass of air takes up more space, its density falls.

2. The warm air is now less dense than the cooler air around it. Less dense air is pushed upwards by the denser air that sinks beneath it.

3. The warm air rises, and cooler, denser air sinks to take its place. The cool air that has sunk now reaches the heater and is warmed in turn.

4. A convection current circulates and carries energy around the room.

A room heater placed low can start a similar circulation in air: warmed air expands and rises, while cooler air moves into the lower region. The process redistributes energy with the air rather than sending every warmed particle directly to every part of the room.

The first hot-air balloons worked this way. In 1783 the Montgolfier brothers in France filled a large bag with air heated by a fire. The hot air inside was less dense than the cooler air around it, so the balloon rose.

Convection needs a fluid that can move

Particles in an ordinary solid remain near fixed positions, so they cannot form this fluid circulation through the material. A liquid or gas can move bodily from one region to another.

More detail (optional)

Fluid can also be moved by a fan or pump. This forced movement can carry energy even when natural circulation is weak.

"Heat rises" is not a complete explanation. Under the stated conditions, the warmer fluid rises because it is less dense than its surroundings. Conduction and radiation can transfer energy in other directions, and a fan can direct fluid flow.

Check your understanding

A sample of water initially at 20 degrees C is heated gently only near its top. Assume ordinary expansion over the temperatures used. Why is natural convection through the whole sample much weaker than when it is heated near the bottom?

  1. Energy travels upwards by heating, so heat supplied at the top cannot spread down through the water.
  2. The warmed, less dense water is already above the cooler, denser water.
  3. The warmed water becomes denser and immediately sinks.
Show the answer

The warmed, less dense water is already above the cooler, denser water.

This arrangement does not drive the same rising-and-returning circulation as bottom heating. Other transfer processes can still warm lower regions; energy is not forbidden from travelling downwards.

04

Thermal radiation

In short

  • Thermal radiation is mostly infrared. It needs no medium, so it crosses a vacuum.
  • Dull black surfaces absorb and emit radiation best. Shiny surfaces reflect it and emit the least.
  • A hotter object, or a larger surface area, radiates more energy each second.

Make a guess. You are not marked.

Two identical metal cans are filled with hot water at the same temperature. One is painted dull black and the other is polished and shiny. Which cools faster?

  1. The dull black can, because it emits infrared faster.
  2. Both the same, because the water starts at the same temperature.
  3. The shiny can, because metal reflects.
Show the answer

The dull black can, because it emits infrared faster.

A dull black surface is a better emitter of infrared radiation than a shiny one, so it loses energy to the surroundings faster and its water cools sooner.

Energy can transfer by electromagnetic radiation across a vacuum. No material medium is needed between the source and the receiver.

Electromagnetic waves can transfer energy. This route differs from conduction through particles and convection with moving fluid.

Ordinary warm objects emit thermal radiation, mainly infrared at everyday temperatures. They need not glow. Radiation from the Sun reaches Earth through space. This shows that air is not needed to carry it.

Objects emit and absorb

An object can emit radiation and absorb radiation from its surroundings at the same time. Its net energy change depends on the difference between what it receives and what it emits.

A hot object in cooler surroundings usually loses energy overall. At thermal equilibrium with surroundings at the same temperature, emission and absorption balance. There is then no net transfer by radiation, even though both carry on.

Radiation transfers energy across a vacuum

Both bodies emit radiation. The arrows show directions, with no numerical rates implied.

Electromagnetic radiation crosses the vacuum between two bodiesA hotter body on the left and a cooler body on the right are separated by a vacuum. One orange arrow goes from left to right and another from right to left, indicating that both bodies emit electromagnetic radiation. Their equal drawn widths indicate directions only, not equal rates. A separate lower arrow identifies net energy transfer from the hotter body towards the cooler body. No material particles travel between them.HotterCoolerVacuumRadiationNet energy: hotter to cooler

Surface colour and texture

Otherwise identical bodies at the same surface temperature, with the same exposed area and surroundings.

Compare emitted radiation: surface colour and textureThe two equally sized surfaces have different finishes. The dull black surface emits radiation at a greater rate than the shiny metallic surface under the stated matching conditions. Otherwise identical bodies at the same surface temperature, with the same exposed area and surroundings. These comparisons concern emitted radiation, not every process involved in an actual cooling experiment.Dull blackShiny metalGreater emissionLess emission

For this usual comparison, dull black is a better emitter. It is also a better absorber of the same incident radiation.

Surface temperature

Same surface finish, exposed area and surroundings; only the surface temperature differs.

Compare emitted radiation: surface temperatureTwo equally sized surfaces have the same finish. The hotter surface emits radiation at a greater rate. No numerical temperature or rate ratio is implied. Same surface finish, exposed area and surroundings; only the surface temperature differs. These comparisons concern emitted radiation, not every process involved in an actual cooling experiment.Cooler surfaceHotter surfaceCoolerHotterLess emissionGreater emission

A hotter surface emits radiation at a greater rate.

Exposed surface area

Same surface finish, surface temperature and surroundings; the exposed surface area differs.

Compare emitted radiation: exposed surface areaThe right exposed surface is larger than the left. Both have the same finish and surface temperature. The larger area gives a greater total emitted rate. This is a qualitative area comparison, with no numerical rate supplied. Same surface finish, surface temperature and surroundings; the exposed surface area differs. These comparisons concern emitted radiation, not every process involved in an actual cooling experiment.Smaller areaLarger areaLess emissionGreater emission

A larger exposed area gives a greater total rate of emission under these conditions.

Net radiative transfer also depends on what is absorbed from the surroundings. Real cooling can include conduction and convection as well.

Radiation can cross the vacuum between source and receiver. Each comparison changes one thing: surface finish, surface temperature or exposed area. The other conditions that matter must be held the same.

Three factors to compare

Surface colour and texture
Compare similar opaque surfaces. A dull black surface is a better absorber and a better emitter of thermal radiation than a shiny metallic surface. The shiny surface reflects a greater fraction of the radiation that falls on it. Compare at the same temperature, exposed area and surroundings.
Surface temperature
With the same surface finish and area, a hotter surface emits energy at a greater rate. To compare net loss, also keep the surroundings the same. The temperature of an object alone does not tell you how much radiation it receives.
Surface area
At the same temperature and with the same finish, a larger exposed surface emits energy at a greater total rate. A larger exposed area also receives more radiation to absorb, if it is lit equally and faces the same way. Use the area actually exposed, not a hidden part of the surface.
More detail (optional)

A comparison should state what is held fixed. If you change both the finish and the temperature, you cannot pick out the effect of finish. A change in the surroundings can alter net transfer even when the surface of the object stays the same.

John Leslie showed the effect of the surface in 1804. He filled a metal cube with hot water, so every face was at the same temperature. The face painted black radiated strongly and the polished face only weakly.

Emission is not the same as net loss. Keep both incoming and outgoing radiation in the explanation. In this comparison a shiny surface is a weaker emitter and absorber. It is not a surface that transfers no energy at all.

Check your understanding

Two opaque metal surfaces have the same exposed area and are both at 80 degrees C in the same cooler surroundings. One is dull black and the other shiny metallic. In the usual thermal-radiation comparison, which emits energy at the greater rate?

  1. Neither can emit unless air carries the radiation away.
  2. The dull black surface.
  3. They must emit at equal rates because their temperatures match.
Show the answer

The dull black surface.

Under the stated comparable conditions, a dull black surface is a better emitter than a shiny metallic surface. Both still emit and absorb radiation; the surface finish changes the rates.

Next, an investigation compares how a dull black can and a shiny can absorb radiation.

05

Investigating surfaces and radiation

Make a guess. You are not marked.

Two identical cans hold the same mass of cold water. One can is dull black and the other is shiny. Both stand the same distance from a lamp for 6 minutes. Which water ends up warmer?

  1. The water in the dull black can.
  2. The water in the shiny can.
  3. Neither. They warm equally, because the lamp and the distance are the same.
Show the answer

The water in the dull black can.

A dull black surface absorbs more of the radiation that reaches it. A shiny surface reflects most of it. So the black can gains energy faster and its water warms more.

To compare how two surfaces absorb radiation, change only the surface and keep everything else the same.

A dull black surface is a better absorber and emitter of thermal radiation than a shiny one. An experiment has to show this with no other difference between the two samples.

Investigate absorption with a fair comparison

Use two metal cans that are the same in every other way, each holding the same mass of water. Give one a dull black outer finish and leave the other shiny. Assume the thin finish changes only the radiation. Its effect on the total mass and on the rest of the thermal response is small enough to ignore.

  1. Keep the samples the same: use the same can material, mass and shape, the same water mass, and the same starting temperature.
  2. Keep the source the same: expose both to the same lamp at equal distances, facing the same way, for the same length of time. Keep the surroundings and air movement the same.
  3. Measure in the same way: place matching thermometers at the same depth in the water, clear of the can walls and base. Use the same lids and the same stirring, if any.
  4. Record the change: read the temperature at the same times, allowing for the response of the sensors. Repeat the comparison from matched starting conditions.
Supplied model readings for the controlled lamp comparison
Time / minDull black can / °CShiny can / °C
02020
22422
42824
63125

Interpret the readings

Compare temperature rises over the same interval

After 6 min, the water in the dull black can has risen by 31 - 20 = 11°C. The water in the shiny can has risen by 25 - 20 = 5°C.

With the matched samples, the greater rise is evidence of greater net energy gain under these conditions. It fits the idea that the dull black surface absorbs radiation better.

The readings do not show that every joule received was kept. Both cans also transfer energy to their surroundings, and conduction carries energy from each warmed can into its water. So the ratio of the temperature rises need not be the ratio of radiation absorbed from the lamp.

More detail (optional)

A can closer to the lamp may receive more radiation for that reason alone. A thermometer touching the lit metal may read a hotter spot there, not the water. Repeating readings does not fix unequal distances or badly placed sensors.

More detail (optional)

A cooling comparison needs the same care. Match the material, mass, shape, starting temperature, sensor placement and surroundings. Dull and shiny surfaces differ in how well they emit radiation. But a simple cooling experiment in air also includes conduction and convection. Do not claim those routes have vanished.

One changed condition, one conclusion. If the cans also differ in distance from the lamp, water mass or starting temperature, a larger rise cannot be blamed on the surface. Repeating an unfair test gives the same unfair result.

Check your understanding

A student shines a lamp on a shiny can and a dull black can of water. The shiny can stands 10 cm from the lamp and the black can 20 cm from it. The water in the shiny can warms more. Which of these is the best conclusion?

  1. No conclusion about the surfaces, because the distance changed as well.
  2. Shiny surfaces absorb radiation better than dull black surfaces.
  3. The result can be trusted if she repeats it with the cans in the same places.
Show the answer

No conclusion about the surfaces, because the distance changed as well.

Two things differ: the surface and the distance from the lamp. The nearer can receives more radiation, so the result cannot be put down to its surface. Repeat with both cans at the same distance.

06

Controlling thermal transfer

Make a guess. You are not marked.

A vacuum flask keeps a drink hot. Which part mainly stops energy transfer by conduction and convection?

  1. The silvered surfaces, which reflect energy back towards the drink.
  2. The plastic cap, which stops hot air escaping from the top.
  3. The vacuum between the walls, which has no particles to pass energy on.
Show the answer

The vacuum between the walls, which has no particles to pass energy on.

Conduction and convection both need particles. A vacuum has almost none, so it blocks both. The silvered walls deal with radiation, and the cap with convection at the top.

In short

  • A vacuum flask: the vacuum gap stops conduction and convection across it, shiny walls cut radiation, and the stopper stops convection at the top.
  • A heat sink does the opposite job: metal conducts, and a large area with moving air carries energy away.
  • To compare two designs fairly, change only one thing at a time.

To explain a thermal design, trace each transfer route. Then say which feature changes it.

Conduction transfers energy as particles act on their neighbours. Convection carries it with moving fluid. Radiation transfers it by electromagnetic waves. A temperature difference sets the direction of net heating. A real design can involve all three processes.

Why a vacuum flask has several features

James Dewar invented the vacuum flask in 1892. It has two walls with an evacuated space between them, reflective surfaces facing that gap, and a stopper at its opening. Each feature deals with a different route.

A flask reduces several routes of energy transfer

This schematic cutaway contains a warm drink in cooler surroundings. Match each numbered feature to its role below.

A vacuum flask with its useful features and remaining conducting routes labelledA warm drink is held in an inner vessel surrounded by an outer wall. Label one points to the evacuated gap between the walls. Label two points to reflective surfaces facing the gap. Label three points to an insulating stopper closing the opening. Label four points to the neck, where solid material joins the inner and outer parts. Label five points to small solid supports beneath the inner vessel. The vacuum reduces conduction and prevents convection across the gap, reflective surfaces reduce radiation, and the stopper reduces transfer through the opening. The neck and supports still provide conducting routes. The drink's headspace is inside the inner vessel and is separate from the vacuum gap.Cooler surroundingsWarmdrink12345Schematic cross-section
  1. Vacuum gap: reduces conduction and prevents convection across the gap.
  2. Reflective faces: reduce radiative transfer between the walls.
  3. Insulating stopper: reduces conduction and movement of fluid through the opening.
  4. Neck: the solid connection still conducts some energy.
  5. Small supports: hold the vessel in place but still provide conducting paths.

The same features also slow energy entering a cold drink from warmer surroundings.

The evacuated gap, reflective surfaces and insulating stopper reduce different transfers. Solid links at the neck and supports can still conduct, so the flask is not a perfect barrier.
Evacuated gap
Removing most gas particles greatly reduces conduction through the gap. It also prevents an ordinary convection current in a fluid there. Radiation can still cross the gap because it does not need particles.
Reflective surfaces facing the gap
Shiny surfaces are poor absorbers and emitters in the usual thermal radiation comparison. They reduce the transfer by radiation across the gap, which the vacuum alone cannot prevent.
Insulating stopper
A stopper of low conductivity slows conduction at the opening. Closing the opening also limits the exchange of fluid between the contents and the surroundings.
Neck and supports
Solid parts that join the inner and outer regions still conduct some energy. The stopper is not a perfect insulator, and the reflective surfaces do not remove all radiation.

Apply the same design twice

A hot drink and a cold drink

  • A drink at 80°C in a 20°C room: net energy transfers out of the drink. The flask slows its cooling.
  • A drink at 5°C in a 25°C room: net energy transfers into the drink. The same barriers slow its warming.

The second case does not need cold to flow out. Reverse the temperature difference and the direction of net transfer reverses. The features still cut down the transfer routes.

Sometimes the aim is faster transfer

A cooling device may use a conducting metal base and fins. Conduction spreads energy from the hotter component into the metal. The fins give a larger exposed area for transfer to the surroundings.

Air moving past the fins carries energy away. A fan can strengthen this fluid movement when natural circulation is not enough. Radiation also plays a part. Its rate depends on the surface finish, temperature and area. Calling every feature an "insulator" would miss the purpose of this design.

Compare designs under the same conditions

To test the effect of an insulating wrap on a cup, change only that wrap. Keep the cup, amount of liquid, lid, starting temperature, surroundings and measurement method the same. Record temperature against time using the same sensor position and intervals.

More detail (optional)

Suppose one cup starts at 80°C and another at 60°C in the same room. The temperature differences that drive the transfer are then not the same. Their final readings alone cannot pick out the effect of the wrap. Resetting the starting conditions fixes that problem. Repeating the unequal comparison does not.

More detail (optional)

Identify where the remaining energy can go: through the cup and lid, into the moving air around it, and by radiation. An improvement should reduce a named route. It should not claim that an extra layer must stop every process.

Match the feature to the mechanism. A vacuum suppresses routes across the gap that need a material medium. A shiny surface reduces transfer by radiation. A solid of low conductivity slows conduction. None of these explains the whole flask by itself.

Check your understanding

Air enters the space that was evacuated between the walls of a vacuum flask. The reflective finishes remain unchanged. What new explanation accounts for faster transfer across this gap?

  1. Radiation can now cross the gap for the first time, because air carries the infrared.
  2. The air stops conduction but makes the walls more reflective.
  3. The air now provides a conduction pathway across the gap and may allow convection within it.
Show the answer

The air now provides a conduction pathway across the gap and may allow convection within it.

The gas provides a material pathway for conduction and, if the geometry allows circulation, convection. The vacuum had suppressed those routes; radiation and conduction through solid connections were already possible.

Revision summary

Start with the temperature difference

Net energy transfers by heating from higher to lower temperature. At thermal equilibrium, temperatures are equal and there is no net heating between the regions. Particles still move. Equal temperature does not establish equal internal energy.

Conduction
In a solid, interactions between vibrating particles transfer energy without bulk flow of the material. Mobile electrons add a mechanism in metals. Good conductors transfer energy more readily under comparable conditions; insulators slow rather than eliminate it.
Convection
Energy is carried with moving liquid or gas. With ordinary expansion, warming increases volume for the same mass, decreasing density. Less dense fluid rises while cooler, denser fluid returns. Explain a complete circulation and its conditions.
Radiation
Electromagnetic waves transfer energy without a material medium. Objects emit and absorb, so net transfer depends on both. Radiation can cross a vacuum.

Retain all three radiation comparisons

  • Colour and texture: dull black is a better absorber and emitter than shiny metallic in the usual comparison of similar opaque surfaces.
  • Temperature: higher surface temperature gives a greater emitted rate when finish and area are unchanged.
  • Area: larger exposed area gives a greater total emitted rate at the same temperature and finish; equal illumination is needed when comparing absorption.

Hold the other conditions fixed. An emitted rate alone is not a net loss.

Explain a design one route at a time

In a vacuum flask, the gap suppresses conduction and convection across it; reflective faces reduce radiation; the stopper limits conduction and fluid exchange at the opening. Neck and support connections remain conduction routes. The same design slows warming of a cold drink and cooling of a hot drink.

For faster cooling, conducting metal spreads energy to exposed surfaces, a larger area supports greater transfer, and moving air carries energy away. The intended result determines which transfers to encourage.

Use measurements to support the explanation

In a surface comparison, match material, mass, geometry, starting temperature, source distance, orientation, surroundings, sensor placement and timing. Compare changes over the same interval. A larger rise in matched samples indicates greater net energy gain under those conditions.

Record temperatures and elapsed times with units. Repeat from the same starting conditions to assess variation, and correct specific causes such as a sensor touching the wrong region or unequal lamp distances. A simple cooling test in air has not removed conduction and convection.

Back to heating and thermal equilibrium

Practise exam questions

Write your answer first, then tick the mark points it makes.

Exam-style question

One end of a metal rod and one end of a glass rod are put in a flame. The other end of the metal rod becomes hot much sooner. Explain how energy is conducted along a metal, and why metals conduct better. [3]

Saved on this browser only. Anyone using this browser can see it.

Exam-style question

An air conditioner is fixed high up on the wall of a room. Explain how it cools the whole room. [3]

Saved on this browser only. Anyone using this browser can see it.

Exam-style question

Two identical metal cans, one painted dull black and one shiny silver, are filled with the same volume of water at 80 °C. After 10 minutes, one can is at 52 °C and the other at 64 °C. State which can is at 52 °C and explain why. Describe the shapes of the temperature-time graphs for the two cans. [3]

Saved on this browser only. Anyone using this browser can see it.

Exam-style question

A vacuum flask keeps hot drinks hot. Explain how each of these features reduces energy transfer: the vacuum between the double walls, the silvered surfaces of the walls, and the stopper. [3]

Saved on this browser only. Anyone using this browser can see it.

Quick recall

Card 1 of 6. Answer in your head, then check.

A metal block at 80 degrees C is pressed against an identical block at 20 degrees C inside an insulated box. Later both read 50 degrees C and the readings stay there. Which of these describes the blocks now? (A) Their particles have stopped moving, because nothing is changing. (B) Energy still flows from the first block to the second, because it started hotter. (C) No net energy transfers between them, although their particles still move.