K223 / K224 / 2027
Radioactivity overview

Full chapter

Radioactivity

All 8 topics and the revision summary on one page.

01

Atoms, nuclei and isotopes

Make a guess. You are not marked.

Carbon-12 and carbon-14 are isotopes of carbon. What is different about their nuclei?

  1. The number of protons: carbon-14 has two more.
  2. The number of neutrons: carbon-14 has two more.
  3. The number of electrons orbiting each nucleus.
Show the answer

The number of neutrons: carbon-14 has two more.

Both are carbon, so both have 6 protons. The nucleon numbers 12 and 14 differ by two, so carbon-14 has 8 neutrons and carbon-12 has 6.

In short

  • The nucleus contains protons and neutrons; electrons move around it.
  • Proton number Z is the number of protons. Nucleon number A is protons plus neutrons.
  • Isotopes have the same number of protons but different numbers of neutrons.

An atom has a tiny positive nucleus, made of protons and neutrons. Negative electrons are outside the nucleus.

Proton
A particle in the nucleus with a charge of +1.
Neutron
A particle in the nucleus with no charge. Protons and neutrons together are called nucleons.
Electron
A particle outside the nucleus with a charge of -1. A neutral atom has as many electrons as protons.

The nucleus is very small: the atom is about 100 000 times as wide. In 1911, Ernest Rutherford showed that the positive charge and most of the mass of an atom are packed into this tiny centre.

Read a nuclide symbol

A nuclide is one kind of nucleus, with a set number of protons and neutrons. Its symbol has the nucleon number A at the top left and the proton number Z at the bottom left.

means sodium-23, with 23 nucleons and 11 protons.

Proton number, Z
The number of protons in the nucleus. It decides which element the atom is.
Nucleon number, A
The number of protons plus neutrons in the nucleus.
Number of neutrons = A - ZA and Z are counts, with no units.

Particles, nuclide symbols and isotopes

A neutral helium-4 atom

The nucleus is drawn far too big. The drawing is not to scale.

Two protons, two neutrons and two electrons in a neutral helium-4 atomA helium-4 atom. Its nucleus holds two protons and two neutrons. Two electrons are outside the nucleus. Two positive protons and two negative electrons make the atom neutral.p+nnp+e-e-NucleusElectrons outside the nucleusp+2 protons; charge +1 eachn2 neutrons; charge 0e-2 electrons; charge -1 each

Read sodium-23's left-hand numbers

Sodium-23: nucleon number 23, proton number 11The symbol Na, for sodium, has 23 at its top left and 11 at its bottom left. So the nucleus has 11 protons and 23 - 11 = 12 neutrons.23 = protons + neutronsNucleon number A2311NaProton number Z11 protonsElement:sodiumNeutrons = 23 - 11 = 12Neutral atom: 11 electrons

Compare neutral atoms

Same proton number identifies the element; different neutron numbers identify its isotopesSodium-23 has 11 protons and 12 neutrons. Sodium-24 has 11 protons and 13 neutrons. Magnesium-24 has 12 protons and 12 neutrons. The two sodium atoms are isotopes. Sodium-24 and magnesium-24 are different elements.2311NaSodium-2311 protons12 neutrons11 electrons2411NaSodium-2411 protons13 neutrons11 electrons2412MgMagnesium-2412 protons12 neutrons12 electronsThe sodium pair: same Z, different ANa-24 and Mg-24: same A, different Z
Compare both numbers before you decide whether two atoms are isotopes.

Isotopes

Isotopes are atoms of the same element with different numbers of neutrons. They have the same proton number but different nucleon numbers.

Sodium-23 has 23 - 11 = 12 neutrons. Sodium-24 also has 11 protons, but 24 - 11 = 13 neutrons. So they are isotopes of sodium.

Magnesium-24 also has nucleon number 24, but it has 12 protons. So it is a different element, not an isotope of sodium.

Isotopes share Z, not A. The same nucleon number does not make two atoms isotopes, so check the proton number first. Adding or removing electrons makes an ion, not a new isotope.

Check your understanding

Three neutral atoms have these nucleon/proton numbers: P has A = 23, Z = 11; Q has A = 24, Z = 11; R has A = 24, Z = 12. Which pair consists of isotopes of the same element?

  1. P and Q, because their proton numbers match while their neutron numbers, and so nucleon numbers, differ.
  2. P and R, because they each have 12 neutrons.
  3. Q and R, because they have the same nucleon number and so the same mass.
Show the answer

P and Q, because their proton numbers match while their neutron numbers, and so nucleon numbers, differ.

Both have Z = 11. P has 23 - 11 = 12 neutrons; Q has 24 - 11 = 13. Isotopes have the same proton number and different neutron numbers.

02

Radioactive decay

Make a guess. You are not marked.

A sealed radioactive source is heated from 20 degrees C to 200 degrees C. What happens to the rate at which its nuclei decay?

  1. It falls, because heating drives the radiation out of the source.
  2. It rises, because the hotter nuclei have more energy and break up faster.
  3. Nothing: the rate of decay stays the same.
Show the answer

Nothing: the rate of decay stays the same.

Radioactive decay is spontaneous. Nothing outside the nucleus, such as temperature or pressure, changes how quickly unstable nuclei decay.

In short

  • An unstable nucleus decays by giving out radiation.
  • Decay is random: you cannot tell when a nucleus will decay.
  • Decay is spontaneous: nothing outside the nucleus makes it happen.

Some nuclei are unstable. An unstable nucleus can decay: it loses energy by giving out radiation. This is radioactive decay.

A nucleus is made of protons and neutrons. In decay, the nucleus itself changes.

Random and spontaneous

Random
You cannot predict when a particular nucleus will decay. Two identical nuclei can decay at very different times.
Spontaneous
Nothing outside the nucleus makes it decay. Heating it, cooling it or changing the pressure does not change the rate of decay.

Picture a huge pile of coins. Each minute you toss them all and remove the ones that land heads. You cannot say which coin will go next, but about half go each minute. A large sample of nuclei is just as predictable, which is why half-life works.

What decay gives out

An unstable nucleus can give out three kinds of radiation: alpha, beta and gamma. The nucleus left behind is called the daughter nucleus, and it may be radioactive too.

All three radiations are ionising. As they pass through matter, they knock electrons out of atoms. The atoms are left charged, as ions. Ionisation is how radiation is detected, and how it damages living cells.

Henri Becquerel discovered radioactivity in 1896. Uranium salts left images on photographic plates wrapped in black paper, even in the dark. The radiation came from the uranium itself.

Define both words. "Random" means you cannot predict when a particular nucleus will decay. "Spontaneous" means nothing outside the nucleus, such as heat or pressure, affects it.

Check your understanding

A large sample of one radioactive nuclide has a reproducible average half-life. What does this tell us about an individual undecayed nucleus?

  1. Its decay time cannot be predicted, although a large sample of such nuclei has a predictable average pattern.
  2. It must decay exactly one half-life after the sample is prepared, like the other nuclei in it.
  3. It needs an external impact to trigger its decay.
Show the answer

Its decay time cannot be predicted, although a large sample of such nuclei has a predictable average pattern.

Random individual events and a reproducible population trend are compatible. The half-life does not identify which nuclei will decay during a particular interval.

03

Alpha, beta and gamma radiation

Make a guess. You are not marked.

A radiation passes through a sheet of paper but is stopped by a few millimetres of aluminium. Which radiation is it?

  1. Gamma, which needs thick lead or concrete to absorb most of it.
  2. Beta, which is more penetrating than alpha but less than gamma.
  3. Alpha, which is stopped by aluminium because it is heavy.
Show the answer

Beta, which is more penetrating than alpha but less than gamma.

Alpha is stopped by paper. Gamma passes through aluminium and needs thick lead or concrete to reduce it greatly. Beta lies between: through paper, stopped by a few millimetres of aluminium.

In short

  • Alpha is stopped by paper, beta by a few mm of aluminium, and gamma is only reduced by thick lead.
  • Alpha is the most ionising and gamma the least.

Alpha, beta and gamma radiation differ in what they are, how strongly they ionise, and how far they get through matter.

All three come from radioactive decay, and all three can ionise atoms.

The three radiations compared
Alpha, αBeta-minus, β-Gamma, γ
What it isA helium nucleus: 2 protons and 2 neutronsA fast electron made in the nucleusAn electromagnetic wave from the nucleus
Charge+2-10
Ionising effectStrongestMediumWeakest
Stopped byPaper, or a few cm of airA few mm of aluminiumOnly reduced by thick lead or concrete

What each radiation is, and what stops it

Arrows show the radiation travelling to the right. These are typical results; a more energetic source gets a little further.

Alpha: low penetration

Alpha: low penetrationAn alpha particle is two protons and two neutrons, a helium nucleus. It travels right from the source and is stopped by a sheet of paper.p+nnp+Helium nucleus2 protons + 2 neutronsCharge +2SourcePaperStoppedby paperTypical resultsNot to scale

A sheet of paper stops alpha particles.

Beta-minus: more penetrating than alpha

Beta-minus: more penetrating than alphaA beta-minus particle is a fast electron made in the nucleus. It passes through paper and is stopped by a few millimetres of aluminium.e-Fast electronMade in the nucleusCharge -1SourcePaperAluminiumTypical resultsNot to scale

Beta passes through paper. A few millimetres of aluminium stops it.

Gamma: the most penetrating

Gamma: the most penetratingGamma rays are electromagnetic waves from the nucleus. They pass through paper and aluminium. Thick lead reduces them, but some still get through.Electromagneticradiation from nucleusNo charge, no massSourcePaperAluminiumLeadTypical resultsNot to scale

Thick lead or concrete reduces gamma rays, but does not stop them all.

Paper stops alpha. A few millimetres of aluminium stops beta. Thick lead only reduces gamma.

Why strong ionisers stop quickly

Each time radiation ionises an atom, it uses up some of its energy. An alpha particle ionises a great many atoms along its path, so it soon runs out of energy. It travels only a few centimetres in air. Gamma rays ionise far fewer atoms, so they travel much further.

So the order for ionising is the reverse of the order for getting through matter.

More detail (optional)

A beta-minus particle is made when a neutron in the nucleus changes into a proton. It is not one of the electrons outside the nucleus.

Paul Villard discovered gamma rays in 1900. Ernest Rutherford, who had already named alpha and beta rays, named them gamma rays in 1903.

Keep the two orders apart. Alpha ionises the most but gets through the least. Gamma ionises the least but gets through the most.

Check your understanding

Alpha particles travel only a few centimetres in air, but gamma rays travel much further. Which statement explains the difference?

  1. Alpha ionises the air strongly, so it soon runs out of energy.
  2. Gamma rays ionise the air more strongly than alpha, and this pushes them further along.
  3. Alpha particles have no charge, so the air molecules can stop them very easily.
Show the answer

Alpha ionises the air strongly, so it soon runs out of energy.

Each ionisation uses up some energy. Alpha is the most strongly ionising radiation, so it gives up its energy within a short distance. Gamma ionises weakly, so it travels much further.

04

Background radiation and count rate

In short

  • Background radiation is all around us, from rocks, cosmic rays, food and the air.
  • Measure the background count rate with no source, then subtract it from each reading.
  • Count rate = counts / time, for example in counts per minute.

A detector picks up some radiation even when no source is near. This background radiation must be taken away from every reading.

Decay is random, so the count goes up and down from one reading to the next.

Where background radiation comes from

  • Rocks, soil and buildings, including radon gas from the ground.
  • Cosmic rays from space.
  • Food: bananas and potatoes are slightly radioactive.
  • Man-made sources, mostly from medicine.

In Singapore, NEA runs 40 stations that measure radiation in the air and water. The background level varies a little from place to place, with the radioactive materials in soil, rock and buildings.

Count rate

Count rate = number of counts / counting timeFor example, in counts/min or counts/s.

Five one-minute readings with no source give 18, 21, 19, 22 and 20 counts. That is 100 counts in 5 min, so the background count rate is 100/5 = 20 counts/min.

Turn counts into rates, then subtract

The counter shows a number of counts. Divide it by the counting time to get a count rate. Teal arrows show some of the radiation.

Background only: 100 counts in 5 min

Background only: 100 counts in 5 minNo source is present. Dashed arrows show background radiation reaching the detector. The counter shows 100 counts in 5 minutes, which is 20 counts per minute.BackgroundNo sourcepresentDetectorCounter total100 countsCounting time / min012345100 / 5 = 20 counts/min

Source plus background: 300 counts in 2 min

Source plus background: 300 counts in 2 minThe source is now next to the same detector, and background radiation still arrives. The counter shows 300 counts in 2 minutes, which is 150 counts per minute. Taking away 20 counts per minute of background leaves 130 from the source.BackgroundSourcepresentDetectorCounter total300 countsCounting time / min012345300 / 2 = 150 counts/min

Source rate = 150 - 20 = 130 counts/min. Subtract rates, not counts, because the two counts took different times.

The two counts took different times, so turn each into a rate before you subtract.

Subtract rates, not counts

300 counts in 2 min with the source

  1. Total rate: 300/2 = 150 counts/min.
  2. Background rate: 100/5 = 20 counts/min.
  3. Corrected count rate: 150 - 20 = 130 counts/min from the source.

Try it step by step

Work it out in steps: Background rate in counts/min, then Rate with the source present in counts/min, then Corrected source rate in counts/min.

  1. Problem 1. With no source present, a detector records 150 counts in 5 minutes. With a source in place it records 420 counts in 2 minutes. Find the count rate due to the source alone.
  2. Problem 2. With no source present, a detector records 120 counts in 4 minutes. With a source in place it records 900 counts in 3 minutes. Find the count rate due to the source alone.
  3. Problem 3. With no source present, a detector records 200 counts in 10 minutes. With a source in place it records 630 counts in 3 minutes. Find the count rate due to the source alone.
Show the answer

Problem 1.

Background rate in counts/min: Background = 150 / 5 = 30 counts/min

Rate with the source present in counts/min: With source = 420 / 2 = 210 counts/min

Corrected source rate in counts/min: Source alone = 210 - 30 = 180 counts/min

Problem 2.

Background rate in counts/min: Background = 120 / 4 = 30 counts/min

Rate with the source present in counts/min: With source = 900 / 3 = 300 counts/min

Corrected source rate in counts/min: Source alone = 300 - 30 = 270 counts/min

Problem 3.

Background rate in counts/min: Background = 200 / 10 = 20 counts/min

Rate with the source present in counts/min: With source = 630 / 3 = 210 counts/min

Corrected source rate in counts/min: Source alone = 210 - 20 = 190 counts/min

Fair readings

Keep the detector, its distance from the source and its settings the same for every reading. Count for longer, or repeat the count, to even out the random ups and downs.

Beyond the syllabus: activity in becquerels (not examined)

The activity of a source is the number of its nuclei that decay each second. Its unit is the becquerel, Bq: 1 Bq is one decay per second.

A detector catches only some of the radiation, so its count rate is smaller than the activity. A count rate of 80 counts/s does not mean an activity of 80 Bq.

Correct every reading. Take the background count rate away from each reading before you use it. Removing the source does not make the reading zero.

Check your understanding

A background measurement records 100 counts in 5.0 min. With the source present, the same setup records 300 counts in 2.0 min. What is the estimated net source count rate?

  1. 130 counts/min
  2. 200 counts/min
  3. 150 counts/min
Show the answer

130 counts/min

The source-plus-background rate is 150 counts/min. Subtract the mean background rate of 20 counts/min to estimate 130 counts/min from the source. A separate calibration is needed to turn this detector rate into an activity estimate.

05

Half-life

Make a guess. You are not marked.

A source has a half-life of 10 minutes. After 20 minutes, what fraction of the original number of undecayed nuclei is left?

  1. One half, because only one more half-life has passed since the first.
  2. None. Two half-lives make a whole.
  3. One quarter, after halving twice.
Show the answer

One quarter, after halving twice.

Twenty minutes is two half-lives. After the first, half remains. After the second, half of that half remains: one quarter.

In short

  • Half-life is the time for half the radioactive nuclei in a sample to decay.
  • After each half-life, the corrected count rate halves.
  • After two half-lives, one quarter remains.

The half-life of a radioactive isotope is the time taken for half of the undecayed nuclei in a sample to decay. In each half-life, the count rate from the sample also halves.

Use the corrected count rate, with the background taken away.

The symbol for half-life is t1/2. It is a time, so it can be in seconds, minutes, hours, days or years. Each isotope has its own half-life. Radon-222, for example, has a half-life of 3.8 days.

Halve, then halve again

Repeated halving

800 counts/min, with a half-life of 6 h

  • After 6 h: 800/2 = 400 counts/min.
  • After 12 h: 400/2 = 200 counts/min.
  • After 18 h: 200/2 = 100 counts/min.

18 h is three half-lives. The fraction left is 1/2 x 1/2 x 1/2 = 1/8, so 7/8 of the nuclei have decayed.

Try it step by step

Work it out in steps: Number of half-lives, then Corrected count rate remaining in counts/min.

  1. Problem 1. A source gives a corrected count rate of 1200 counts/min. Its half-life is 8 minutes. What will the corrected count rate be after 24 minutes?
  2. Problem 2. A source gives a corrected count rate of 640 counts/min. Its half-life is 5 hours. What will the corrected count rate be after 20 hours?
  3. Problem 3. A source gives a corrected count rate of 2000 counts/min. Its half-life is 3 days. What will the corrected count rate be after 12 days?
Show the answer

Problem 1.

Number of half-lives: 24 / 8 = 3 half-lives

Corrected count rate remaining in counts/min: 1200 -> 600 -> 300 -> 150 counts/min

Problem 2.

Number of half-lives: 20 / 5 = 4 half-lives

Corrected count rate remaining in counts/min: 640 -> 320 -> 160 -> 80 -> 40 counts/min

Problem 3.

Number of half-lives: 12 / 3 = 4 half-lives

Corrected count rate remaining in counts/min: 2000 -> 1000 -> 500 -> 250 -> 125 counts/min

The sample does not vanish. The nuclei that decay become daughter nuclei, which are still there. After the next half-life, half of the nuclei that are left decay.

Watch out for this

A student says: "After two half-lives, none of the radioactive nuclei are left." What is wrong with this?

Show the answer

Each half-life halves the number that remain, not the original number. After two half-lives, one quarter of the original nuclei are still undecayed.

Halve what is left, once for each half-life. After two half-lives, a quarter is left, not none. Do not divide by the number of half-lives.

06

Finding half-life from readings and graphs

Make a guess. You are not marked.

A detector is placed near a radioactive source with a short half-life, and its total count rate is recorded for a long time. What happens to the total count rate in the end?

  1. It levels off at the background count rate.
  2. It keeps falling by the same number of counts in every half-life.
  3. It falls to zero once the source has decayed.
Show the answer

It levels off at the background count rate.

The part from the source keeps halving towards zero, but the background radiation stays. So the total settles at the background, not at zero.

In short

  • Take the background away from each reading first.
  • The half-life is the time for the corrected count rate to halve.

To find a half-life from readings, first take away the background. Then find the time for the corrected count rate to halve.

Half-life is the time for the count rate from a source to halve.

From a table

A detector near a source gives these total count rates. The background is 20 counts/min.

Take the same background from each total.
Time / minTotal / (counts/min)Corrected / (counts/min)
0180160
410080
86040
124020
163010

Take away the background before finding the half-life

A smooth model of one source, with a steady background of 20 counts/min. Real readings scatter around such a curve.

Total count rate includes the background

Total count rate includes the backgroundCount rate in counts per minute against time in minutes. The total count rate is 180 at 0 min, 100 at 4 min, 60 at 8 min, 40 at 12 min and 30 at 16 min. A dashed line marks the background of 20 counts per minute. The curve levels off towards this line, not towards zero.Count rate / counts per min02040801201602000481216Time / min

The dashed line is the 20 counts/min background. The total curve approaches that level, rather than zero.

Corrected count rate: subtract 20 counts/min

Corrected count rate: subtract 20 counts/minOn the same axes, the corrected count rate is 160, 80, 40, 20 and 10 counts per minute at 0, 4, 8, 12 and 16 min. Two shaded intervals, 0 to 4 min and 8 to 12 min, each last 4 min: 160 halves to 80, and 40 halves to 20.Count rate / counts per min02040801201602000481216Time / min4 min160 to 804 min40 to 20

160 to 80 and 40 to 20 counts/min each take 4 min. The corrected rate gets closer and closer to zero.

Both graphs use the same scales. Each dot is a value from the table.

The total curve levels off at the background of 20 counts/min. The corrected curve heads towards zero.
  1. Correct the readings: 180 - 20 = 160 and 100 - 20 = 80 counts/min.
  2. Find the time to halve: 160 to 80 takes 4 min.
  3. Check another pair: 40 at 8 min to 20 at 12 min also takes 4 min. So the half-life is 4 min.

Halving the total instead, from 180 to 90, would halve the background too. The background does not decay, so the answer would be wrong.

From a graph

Pick a corrected count rate on the curve and find half of it. Read the time between the two. Do the same for a second pair to check, and draw the lines on the graph to show your working.

Real readings scatter above and below a smooth curve, because decay is random. Draw a smooth curve of best fit through them.

Ernest Rutherford discovered the principle of half-life in 1907.

Graph reader

Find a half-life from measured counts

A detector records the total count rate from a source plus background. Move the time cursor to read the graph.

050100150200250300051015202530time / mincount rate / (counts/min)

Correct before you halve. Take the background away from each reading first. Halving the raw readings gives the wrong half-life.

Check your understanding

A single-nuclide model has background 20 counts/min. Its total rates are 180 counts/min at 0 min, 100 at 4 min and 60 at 8 min. What half-life follows from these readings?

  1. It cannot be found until the total rate reaches zero.
  2. 4 min: the corrected rate falls from 160 to 80, then from 80 to 40 counts/min.
  3. Between 4 and 8 min, when the total rate falls from 180 to 90 counts/min.
Show the answer

4 min: the corrected rate falls from 160 to 80, then from 80 to 40 counts/min.

Both corrected halving intervals last 4 min under unchanged detection conditions. Equal time intervals halve the remaining source contribution; they do not subtract an equal number of counts each time.

07

Uses of radioactivity

Make a guess. You are not marked.

A paper mill checks paper thickness with a source on one side of the sheet and a detector on the other. Which radiation should it use?

  1. Gamma, because it passes straight through and is easy to detect.
  2. Alpha, because any sheet of paper stops it before it reaches the detector.
  3. Beta, because paper partly absorbs it, so the count changes with thickness.
Show the answer

Beta, because paper partly absorbs it, so the count changes with thickness.

Beta passes through paper but is partly absorbed, so a thicker sheet gives a lower count. The change in count can control the rollers.

In short

  • Uses include tracers, thickness gauges, smoke alarms and cancer treatment.
  • Each use needs radiation that gets through the right amount of matter.

Each use of radioactivity needs radiation that gets through the right amount of matter. Some uses also rely on its ionising effect.

Alpha is stopped by paper, beta by a few millimetres of aluminium, and gamma only by thick lead or concrete.

Thickness gauge: beta

A beta source and a detector sit on either side of a moving sheet of paper. A thicker sheet absorbs more beta, so the count rate falls. A thinner sheet lets more through. The machine adjusts its rollers to keep the count rate steady.

Medical tracer: gamma

A small amount of a gamma source is put into a patient's body. Gamma rays get out of the body, so a camera outside can show where the tracer has gone.

Smoke alarm: alpha

Americium-241 gives out alpha particles. They ionise the air between two plates, so a small current flows. Smoke particles pick up the ions, so the current falls and the alarm sounds.

Cancer treatment: gamma

Beams of gamma rays from a cobalt-60 source are aimed at a tumour. They ionise its cells and kill them. Many hospitals now use high-energy X-rays from machines called linear accelerators in the same way. Healthy cells nearby can be harmed too, so the dose is carefully controlled.

Two uses: a thickness gauge and a tracer

Brown dots are radioactive material. Teal arrows show radiation. Blue arrows show the sheet moving.

Thinner sheet: a larger detector rate

Thinner sheet: a larger detector rateA beta source on the left and a detector on the right, with a thin moving sheet between them. Most of the radiation gets through to the detector, so the count rate is larger.BetasourceSheetDetectorSheetmotion

Thicker sheet: a smaller detector rate

Thicker sheet: a smaller detector rateThe same source and detector, with a thicker sheet of the same material. More of the radiation is absorbed in the sheet, so the count rate is smaller.BetasourceSheetDetectorSheetmotion

The gauge works because the sheet absorbs some but not all of the radiation.

A tracer is an internal source

Gamma radiation travels from an internal tracer to an external detectorRadioactive tracer inside a body gives out gamma rays. Some travel out of the body to a detector outside.RadioactivetracerDetectorBody

The source is inside the body and the detector is outside. Gamma rays get out of the body to reach it.

A gauge uses radiation that passes partly through a sheet. A tracer uses radiation that gets out of the body.

Americium-241 has a half-life of about 430 years. So the activity of a smoke alarm's source hardly falls during the life of the alarm.

Explain all three radiations. For a paper gauge, say why alpha would not work: paper stops it all. Say why gamma would not work: it passes through almost unchanged. Then say why beta works: paper absorbs some of it.

Check your understanding

A hospital puts a small amount of a radioactive tracer into a patient and follows it with a camera outside the body. Which of these should the tracer give out?

  1. Beta particles, because the body stops them, which makes them safe.
  2. Alpha particles, because they ionise strongly and so are easy to detect.
  3. Gamma rays, because they can pass out of the body to the camera.
Show the answer

Gamma rays, because they can pass out of the body to the camera.

Gamma is the most penetrating radiation, so it gets out through the body. It is also the weakest ioniser, which keeps the harm to the patient's cells low.

08

Hazards and safety

Make a guess. You are not marked.

A worker stands near a sealed gamma source for a few minutes, then walks away. Is the worker now radioactive?

  1. No. Radiation reached the worker, but no radioactive material was left on or in them.
  2. Yes, for one half-life of the source.
  3. Yes, because the gamma rays passed through the worker's body.
Show the answer

No. Radiation reached the worker, but no radioactive material was left on or in them.

This is irradiation. Once the worker moves away, the exposure stops. Only contamination, radioactive material on or in the body, keeps giving out radiation.

In short

  • Radiation can damage or kill living cells, and can cause cancer.
  • Keep your distance, limit the time and use shielding.

Ionising radiation can damage or kill living cells. The harm depends on the radiation, how much of it you get, and where the source is.

All three radiations ionise atoms. In a living cell, this can damage its DNA.

The harm radiation does

A large dose in a short time can kill many cells and make a person ill quickly. A smaller dose can damage the DNA in a cell. The cell may then grow out of control, which can lead to cancer.

Irradiation and contamination

Irradiation
Radiation from a source reaches you. When you move away from the source, the exposure stops. You do not become radioactive.
Contamination
Radioactive material gets onto your skin or clothes, or inside your body. It keeps giving out radiation until it is removed or has decayed.

Irradiation or contamination?

Brown dots are radioactive material. Teal arrows show radiation.

Irradiation: radiation reaches the object

External irradiation without transferring radioactive materialA source on the left gives out radiation that reaches an object on the right. No radioactive material gets onto or into the object.ExternalsourceObjectSource material remains outside

Contamination: radioactive material is present

Radioactive material on or inside an objectRadioactive material is now on the surface of the object and inside it, and keeps giving out radiation from there.ObjectOn the surfaceInsideBrown dots represent source material

Irradiation: radiation reaches an object. Contamination: radioactive material is on or inside it. Both can happen at once.

Irradiation: radiation reaches an object. Contamination: radioactive material is on or inside it.

Outside or inside the body

Outside the body, alpha is the least harmful, because the outer layer of skin stops it. Inside the body, it is the most harmful. If an alpha source is swallowed or breathed in, it ionises the cells right next to it very strongly.

Radon is an example. This radioactive gas seeps out of rocks and soil and gives out alpha particles. Breathing in high levels of it for many years can cause lung cancer.

Staying safe

  • Distance: handle sources with long tongs, and keep away from them.
  • Time: spend as little time near a source as you can.
  • Shielding: store sources in lead-lined boxes, and work behind screens.
  • Containment: keep sources sealed and wear gloves, so that no radioactive material escapes.

In Singapore, NEA's Radiation Protection and Nuclear Science Group licenses anyone who imports, sells, keeps or uses radioactive materials. It also controls how radioactive waste is disposed of.

Irradiated does not mean radioactive. Alpha, beta or gamma radiation passing through you does not make you radioactive. Only contamination leaves radioactive material behind.

Check your understanding

Typical alpha particles are stopped by paper or the outer layer of intact skin. Why can an alpha-emitting material inside the body still be hazardous?

  1. Anything stopped by paper is harmless in every location, inside or outside the body.
  2. Gamma radiation is the one that damages cells, because it is the most penetrating.
  3. It emits strongly ionising particles straight into nearby living cells.
Show the answer

It emits strongly ionising particles straight into nearby living cells.

Low penetration means a short range, not an absence of energy transfer. Internal alpha-emitting material can cause intense local ionisation. The source's location and the exposure conditions matter.

Revision summary

Atoms, nuclei and isotopes

Proton number Z = number of protons; it decides the element. Nucleon number A = protons + neutrons. Neutrons = A - Z. Isotopes have the same Z but different numbers of neutrons.

Radioactive decay

An unstable nucleus loses energy by giving out radiation. Decay is random (you cannot predict when a nucleus will decay) and spontaneous (heat or pressure do not affect it). All three radiations ionise atoms.

Alpha, beta and gamma

  • Alpha: helium nucleus, charge +2. Most ionising; stopped by paper or a few cm of air.
  • Beta-minus: fast electron from the nucleus, charge -1. Stopped by a few mm of aluminium.
  • Gamma: electromagnetic wave, no charge. Least ionising; only reduced by thick lead or concrete.

Background radiation and count rate

Count rate = counts / time
Corrected count rate = count rate - background count rate
Subtract rates, not counts.

Background comes from rocks, soil and buildings (including radon), cosmic rays, food and man-made sources.

Half-life

The time for half of the undecayed nuclei in a sample to decay. After 1, 2 and 3 half-lives, 1/2, 1/4 and 1/8 are left. Example: 800 counts/min with a half-life of 6 h becomes 100 counts/min after 18 h.

Half-life from readings and graphs

Take the background from each reading, then find the time for the corrected count rate to halve. Check with a second pair. The total count rate levels off at the background, not zero.

Uses of radioactivity

Thickness gauge: beta. Medical tracer: gamma. Smoke alarm: alpha. Cancer treatment: gamma.

Hazards and safety

Ionisation damages or kills cells and can cause cancer. Irradiation does not make you radioactive; contamination leaves radioactive material on or in you. Alpha is most harmful inside the body. Stay safe with distance, short times, shielding and sealed sources.

Back to the first lesson

Practise exam questions

Write your answer first, then tick the mark points it makes.

Exam-style question

A sample contains 80 g of a radioactive isotope with a half-life of 6.0 days. Calculate the mass of this isotope that remains undecayed after 18 days. [2]

Saved on this browser only. Anyone using this browser can see it.

Exam-style question

Define half-life. [1]

Saved on this browser only. Anyone using this browser can see it.

Exam-style question

Name the type of radiation, alpha, beta or gamma, that is described by each statement: (a) it is stopped by a sheet of paper; (b) it passes through paper but is stopped by a few millimetres of aluminium; (c) it is only reduced by thick lead or concrete. [3]

Saved on this browser only. Anyone using this browser can see it.

Quick recall

Card 1 of 7. Answer in your head, then check.

Three neutral atoms have these nucleon/proton numbers: P has A = 23, Z = 11; Q has A = 24, Z = 11; R has A = 24, Z = 12. Which pair consists of isotopes of the same element?