K224 / K225 / 2027

Lesson 11 of 11 / Biological molecules

Sources of error and their effect

Why does "human error" earn no marks?

I can state a source of error with its effect on the result, and give an improvement that fixes it.

  • I can investigate and explain temperature and pH effects on enzyme reactions.Syllabus

    Syllabus K224 / K225, Topic 3(e). Investigate and explain temperature and pH effects on enzyme reactions.

About 3 min

Make a guess. You are not marked.

A student writes "human error" as the source of error in her amylase experiment. Why does this earn no mark?

  1. Because only faulty equipment counts as a source of error.
  2. It names no exact problem and no effect.
  3. Because a careful student makes no errors.
Show the answer

It names no exact problem and no effect.

A source of error must say what in the method went wrong and which way it pushed the reading.

The key idea

Every source of error needs its effect: name the exact problem, say which way it pushes the reading, then give an improvement that fixes that problem.

A source of error is a feature of the method that makes a reading differ from its true value.

Explore the idea

Which way does each error push the time?

True time and recorded time for starch to disappearTwo bars. The true time is 65 seconds. With this source of error, the recorded time is 70 seconds, which is too long.True time65 sRecorded70 s

Problem: The blue-black colour fades gradually, so the end point is recorded late. Effect: The time is too long, so the calculated rate is too low. Improvement: Compare each spot with a reference spot of iodine and water.

Invented values that show only the direction of each error. All three errors make the recorded time longer than the true time.

Explanation

Every source of error needs its effect. "Human error" scores nothing. Name the exact problem and say which way it pushes the reading.

For example, the blue-black colour fades slowly, so you may record the end point too late, making the time too long. Compare each drop with a spot of iodine and water.

Here is another example. If the solutions are mixed before they reach the water-bath temperature, the time will be too long. Leave them in the water bath for 5 minutes first.

A third example is how often you take a sample. If you test a drop only every 30 s, the real end point could be up to 30 s earlier than the one you record. Test a drop every 10 s.

Step by step
  1. 1

    Name the exact problem

    Say what in the method goes wrong, such as an end point that is hard to judge.

  2. 2

    Give the effect

    Say whether the reading becomes too high or too low, and what that does to the rate.

  3. 3

    Give the improvement

    The improvement must fix that particular problem, such as warming both solutions before mixing.

Worked example

Fix the cold-start problem

A student times how long amylase takes to digest starch at 40 degrees C. She mixes room-temperature solutions and then puts the tube in the 40 degrees C water bath. State the source of error, its effect on the time and an improvement.

One way to explain it

The mixture starts below 40 degrees C, so for the first part of the experiment the enzyme works at a lower temperature. The recorded time is too long, so the rate is underestimated. Leave the starch and the amylase in separate tubes in the 40 degrees C water bath for 5 minutes before mixing.

Why this answer works
  • Name the exact problem, not "human error".
  • Give the direction of the effect on the reading and on the rate.
  • The improvement fixes that particular problem.

Watch out for this

A student says: "Repeating the experiment removes a source of error." What is wrong with this?

Show the answer

Repeats let you spot an anomalous reading and calculate a mean. An error built into the method, such as a late end point, affects every repeat in the same way. Change the method to fix it.

Check your understanding

A student lifts the tube out of a 40 degrees C water bath each time she takes a sample. The room is at 25 degrees C. What is the effect on the time for starch to disappear?

  1. There is no effect, because the tube goes back into the water bath each time.
  2. The mixture cools, so the enzyme is denatured and the time is too short.
  3. The mixture cools, so the reaction slows and the time is too long.
  4. This is human error, so its effect cannot be stated.
Show the answer

The mixture cools, so the reaction slows and the time is too long.

Below the optimum, a lower temperature means fewer effective collisions. The exact problem is cooling and its effect is a longer time.

Quick recall

Card 1 of 3. Answer in your head, then check.

Why does "human error" earn no marks?

You can return to this lesson any time.