K224 / K225 / 2027

Lesson 9 of 11 / Biological molecules

Drawing a results table

What earns the marks in a results table?

I can draw a results table with correct columns, headings, units and decimal places.

  • I can investigate and explain temperature and pH effects on enzyme reactions.Syllabus

    Syllabus K224 / K225, Topic 3(e). Investigate and explain temperature and pH effects on enzyme reactions.

About 4 min

Make a guess. You are not marked.

You time a reaction with a stopwatch and get 43 seconds. Where does the unit "s" go in your results table?

  1. After the number in every cell.
  2. Nowhere. A table does not need units.
  3. In the column heading only.
Show the answer

In the column heading only.

Headings are written quantity / unit, such as "Time / s". The cells then hold only numbers.

The key idea

A results table puts the independent variable in the first column, the unit only in each heading, and every reading in a column to the same number of decimal places.

The independent variable is the factor you change on purpose. The dependent variable is the factor you measure. Compare the draft table with the corrected one below.

Explore the idea

Would this table earn the marks?

Draft: amylase results
TempTimeTimeTime
20182 s176179.0
309490 s98
40414543.0
50667164
60300300300

Find five problems before you switch to the marked layout: look at the headings, the units, the decimal places, the missing column and the 60 degrees C row.

Test tube and control tube in the amylase investigationBoth tubes hold starch solution in a water bath at 40 degrees C. The test tube has active amylase. The control tube has amylase that was boiled and then cooled. After 300 seconds, an iodine spot from the test tube is yellow-brown, so starch has gone. The spot from the control tube is blue-black, so starch remains. Only active enzyme makes the starch disappear.Test tubeactive amylase+ starchControl tubeboiled, cooledamylase + starchWater bath, 40 degrees CIodine, 300 sYellow-brownstarch goneBlue-blackstarch remains

Control: the only difference between the two tubes is that the control enzyme was boiled, which denatures it. Starch remains in the control tube, so active amylase, not heat or time, made the starch disappear in the test tube.

Original practice values, not measured data. The two tubes look the same at the start; only the iodine spots at the end show which one had active enzyme.

Explanation

In practical questions, the results table earns marks before the biology does. Draw the table with a ruler, with a border and lines between the columns. Put the independent variable, the factor you change (such as temperature), in the first column. Put each repeat of the dependent variable, the factor you measure (such as time), in its own column, then a column for the mean.

Each heading has a quantity and a unit, written "Temperature / degrees C" or "Time / s". Put the unit in the heading only, never in the boxes. Give every reading in a column to the same number of decimal places. A stopwatch read to the nearest second gives whole numbers, so write "43", not "43.0". Give the mean to the same number of decimal places.

Sometimes a reaction does not finish in the time you allow. If starch is still there after 300 s, write "> 300". Do not make up a number, and do not use it in a mean.

Step by step
  1. 1

    Lay out the columns

    Independent variable first, then repeats, then mean. Rule the lines.

  2. 2

    Write the headings

    Quantity / unit in each heading. No units in the cells.

  3. 3

    Check the numbers

    Same decimal places down each column, and the mean to the same number of places.

Worked example

Fill in the mean column

Amylase digests starch at 30 degrees C in 85 s, 88 s and 91 s in three repeats. The stopwatch was read to the nearest second. What goes in the mean column, and what is its heading?

One way to explain it

The mean is (85 + 88 + 91) / 3 = 88. Write 88 in the cell, with no unit and no decimal place, under the heading "Mean time for starch to disappear / s".

Why this answer works
  • Add the three repeats and divide by 3.
  • The readings are whole seconds, so the mean is a whole number too.
  • The unit belongs in the heading, not in the cell.

Watch out for this

A student says: "Writing the unit after every number in a results table makes it clearer." What is wrong with this?

Show the answer

The unit goes once, in the column heading, written as quantity / unit. A cell holds only the number, so "43" is right and "43 s" is wrong.

Check your understanding

A stopwatch is read to the nearest second. Which entry is correct for one cell under the heading "Time for starch to disappear / s"?

  1. 43
  2. 43.0
  3. 43 s
  4. 0.72 min
Show the answer

43

The cell holds only the number, to the precision of the instrument. The unit is already in the heading.

Quick recall

Card 1 of 3. Answer in your head, then check.

What earns the marks in a results table?

You can return to this lesson any time.