K326 / K327 / 2027
D.C. circuits overview

Lesson 2 of 7

Series and parallel connections

  • I can draw circuit diagrams using every component and source listed for this course.Syllabus

    Syllabus K326 / K327, 13(a). Draw circuit diagrams using every component and source listed for this course.

Make a guess. You are not marked.

Two wires cross on a circuit diagram, with no dot where they cross. What does that mean?

  1. They are joined if the two wires carry the same current.
  2. They are not connected; the current in each stays on its own wire.
  3. They are joined, because every crossing on a diagram is a junction.
Show the answer

They are not connected; the current in each stays on its own wire.

A junction is shown by a dot. Wires that cross without a dot pass over each other, so no current flows from one to the other.

Whether parts are in series or in parallel depends on what they are joined to, not on where they sit on the page.

A circuit diagram uses standard symbols joined by straight lines for the wires.

Junctions and crossing wires

A junction is a point where wires join. Draw it as a dot. Where two wires cross without joining, leave out the dot, or draw a small bridge in one of the wires. Do not add a dot just because two lines pass close together.

Wires joined with no part between them act as one connection point, called a node. There is no p.d. between any two points on it. A wire can bend or take a longer route on the page and still be the same node.

Series or parallel?

Series
The parts are on one path, one after another. The current does not split between them, so the same current passes through each part.
Parallel
The parts are joined to the same two nodes, at both ends. Sharing just one point is not enough.

Older Christmas light sets had their bulbs wired in series, on one path. In a parallel set, each bulb has its own path between the same two wires.

Follow the connections, not the positions

A dot shows where wires join. Both drawings show the same network of three resistors. A cell could be joined across A and C.

One drawing of the network

One drawing of the networkR1 joins A to B. R2 joins B to C along the upper path, and R3 joins the same B and C along the lower path. Upright wires at B and C join the upper and lower junctions. No plain wire joins B straight to C.ABCR1R2R3R1: A/B; R2 and R3: B/C

Move R3 around the outside

Move R3 around the outsideThe same network is drawn again. A joins the left end of R1, and R1 ends at B. R2 joins B to C. From B, a wire goes up to the right end of R3. The left end of R3 goes round the left and bottom edges to C. The outer path has R3 in it, so it is not a short circuit. No wires cross.ABCR1R2R3The connections have not changed
Both drawings keep R1 between A and B, and R2 and R3 each between B and C. So R2 and R3 are in parallel. R1 is in series with that whole parallel group, wherever the symbols sit on the page.

R1 carries the current going into the R2 and R3 group. That does not mean R1 has the same current as R2 or R3 on its own. The current splits at B.

Redraw without changing the circuit

To redraw a circuit, first write down the two end points of every part. Keep each part between the same two points as you move it. A plain wire added straight from B to C would change the circuit. The current would take that wire instead of going through R2 and R3.

Meters follow the same rule. An ammeter goes in series in the path you want to measure. A voltmeter joins the two ends of the part or group you want to measure.

Sharing one point does not make parts parallel. R1 and R2 both touch B, but R1 joins A to B and R2 joins B to C. Parallel parts share both of their end points.

Check your understanding

R1 connects A to B. R2 and R3 each connect B to C, with no plain wire directly joining B to C. Which of these descriptions remains correct when the drawing is rearranged?

  1. R2 and R3 are in parallel with each other, and R1 is in series with their combination.
  2. The three resistors are in series, because they appear one after another in the drawing.
  3. R1 and R2 are parallel because they both connect to B.
Show the answer

R2 and R3 are in parallel with each other, and R1 is in series with their combination.

R2 and R3 share both endpoints, B and C. R1 carries the current entering or leaving that whole parallel group. Moving symbols on the page does not change these connections.