K326 / K327 / 2027
Electric charge and current of electricity overview

Lesson 6 of 6

Resistance of a wire

  • I can apply wire-resistance proportionality to length and cross-sectional area.Syllabus

    Syllabus K326 / K327, 12(j). Apply wire-resistance proportionality to length and cross-sectional area.

Make a guess. You are not marked.

A wire has a resistance of 4 ohm. A second wire of the same material and the same thickness is twice as long. What is its resistance?

  1. 4 ohm, the same.
  2. 8 ohm, twice as much.
  3. 2 ohm, half as much.
Show the answer

8 ohm, twice as much.

Resistance is proportional to length for the same material and cross-section. Charge has twice as much wire to pass through, so the resistance doubles.

A longer wire has more resistance, and a thicker wire has less. For wires of the same material at the same temperature, R is proportional to length and inversely proportional to cross-sectional area.

Resistance is V/I, measured in ohms. Compare wires made of the same material at the same temperature. A change in either one also changes the resistance.

The heating wire in toasters and electric kettles is often nichrome, a mix of nickel and chromium. A nichrome wire has about 66 times the resistance of a copper wire of the same length and thickness.

Longer wire, more resistance
Resistance is proportional to length: R ∝ L. Double the length with the same thickness, and the resistance doubles. The charge has twice as much wire to pass through.
Thicker wire, less resistance
Resistance is inversely proportional to cross-sectional area: R ∝ 1/A. Double the area with the same length, and the resistance halves. A wider wire gives the charge more room to flow.

The cross-sectional area is the area of the wire's cut end: the circle you see if you slice it across. It is not the curved outside surface. For a round wire, A = πd2/4, so the area depends on the square of the diameter d.

Double the length and double the diameter

Both wires are the same material at the same temperature. The drawings use the same scale. The labels give ratios, not sizes to measure on your screen. The area is the circle at the cut end.

Original wire: 8.0 ohm

Original wire: 8.0 ohmThe first wire has length L, diameter d and cross-sectional area A. Its resistance is 8.0 ohm. A side view and an end-on circle show its size. The length is measured between the two ends. The diameter brackets span the wire and the end circle.Side viewLdEnd-on cross-sectionAd

Changed wire: 4.0 ohm

Changed wire: 4.0 ohmThe second wire is twice as long and has twice the diameter. Its end circle has twice the radius and four times the area. It is the same material at the same temperature, so its resistance is 2/4, or half, of 8.0 ohm: 4.0 ohm. The length is measured between the two ends. The diameter brackets span the wire and the end circle.Side view2L2dEnd-on cross-section4A2d

Twice the diameter gives four times the cross-sectional area. The resistance changes by 2/4 = 1/2, so 8.0 Ω becomes 4.0 Ω.

The second wire is twice as long and twice as wide. Its cut end has four times the area. Both wires are the same material at the same temperature, so the two changes together halve the resistance.

One change at a time

Twice the length and twice the diameter

The first wire has a resistance of 8.0 Ω.

  1. Twice the length multiplies the resistance by 2.
  2. Twice the diameter gives 22 = 4 times the area. That divides the resistance by 4.
  3. Together: new R = 8.0 x 2/4 = 4.0 Ω.

In general, for the same material and temperature: Rnew/Rold = (Lnew/Lold) x (Aold/Anew).

Investigate how length affects resistance

Use one wire that has the same thickness all along it. Clip two contacts onto it, and measure the length between them with a ruler. Only this active length carries the current.

  1. Keep the material and the thickness the same. Use several different active lengths.
  2. At each length, record the current through that part of the wire and the p.d. across it. Work out R = V/I.
  3. Keep the current small and switch off between readings. This stops the wire heating up, which would change its resistance.
  4. Plot R against length. A straight line through the origin shows that R is proportional to length.

To find the area, measure the diameter with a micrometer. Check it for zero error, and measure at several places along the wire. Change the diameter to metres before you work out the area.

The contacts and leads can add a little resistance of their own. A wire whose diameter changes along its length is not uniform. Repeat readings show how much they scatter, but they do not remove these effects. Name the problem and say how your method deals with it.

Twice the diameter is four times the area. So doubling the diameter gives a quarter of the resistance, not half.

Check your understanding

A wire has resistance 8.0 ohm. A second wire of the same material and temperature has twice its length and twice its diameter. What is the second resistance?

  1. 8.0 ohm: the doubled length and diameter cancel.
  2. 16 ohm: the wire is twice as long.
  3. 4.0 ohm: length factor 2, area factor 4.
Show the answer

4.0 ohm: length factor 2, area factor 4.

For the same material and temperature, R is proportional to L/A. The new resistance is 8.0 x 2 / 4 = 4.0 ohm.