Skip to notes
K326 / K328 / 2027
Particles and Atoms

Lesson 2 of 4

Changes of state and heating curves

Explain melting, boiling, evaporation and freezing, and read the flat parts of heating and cooling curves.

O-Level 5086 / 5088 (2026) / SEC G3 K326 / K328 (2027)

  • I can explain states and their interconversion.Syllabus

    Syllabus K326 / K328, 2.1(a). Explain states and their interconversion

Changes of state and heating curves

Melting and boiling take in energy to overcome the attractions between particles, so a pure substance stays at a constant temperature while it changes state.

Make a guess. You are not marked.

Crushed ice at 0 degrees C is heated steadily and stirred. What does the thermometer show while the ice is melting?

  1. It rises steadily the whole time it is heated
  2. It stays at 0 degrees C while ice melts
  3. It drops below 0 degrees C first, then rises
Show the answer

It stays at 0 degrees C while ice melts

The energy supplied overcomes the attractions between particles instead of making them move faster, so the temperature stays constant.

Heating and cooling
  1. Solid to liquid: melting

    Particles take in energy and vibrate more. At the melting point, they overcome enough of the attractions to slide past one another.

  2. Liquid to gas: boiling or evaporation

    Particles take in energy and overcome the attractions between them, so they escape and spread far apart. Boiling happens throughout the liquid at its boiling point. Evaporation happens only at the surface and can happen below the boiling point.

  3. Gas to liquid: condensation

    Particles lose energy, move closer together and are held by attractions again. Energy is given out to the surroundings.

  4. Liquid to solid: freezing

    Particles lose energy and settle into fixed positions in a regular pattern. Energy is given out to the surroundings.

  5. Solid to gas: sublimation

    Some solids, such as dry ice (solid carbon dioxide) and iodine, turn straight into a gas without melting. The reverse change, gas straight to solid, is called deposition.

Evaporation explains why wet laundry dries in Singapore. Daytime temperatures there usually reach only 31 to 33 °C, far below the boiling point of water, 100 °C. Even so, some water particles at the surface have enough energy to escape into the air.

When a substance is heated and stays in the same state, its particles gain kinetic energy and move faster, so its temperature rises. Temperature measures the average kinetic energy of the particles. While a pure substance melts or boils, the energy it takes in overcomes the attractions between particles instead of speeding them up. So the temperature stays constant until the change of state is complete.

Heating a pure substance

The temperature rises while the substance is solid. It stays flat at the melting point, where solid and liquid are both present, and rises again for the liquid. It stays flat for longer at the boiling point, where liquid and gas are both present, then rises for the gas.

Schematic curve for steady heating at constant pressure; no temperatures are implied. Boiling lasts longer than melting because separating the particles completely takes more energy.

Check your understanding

Ice is melting while its temperature stays constant. Is it absorbing energy?

  1. No. The temperature is steady, so no energy is entering or leaving the ice.
  2. Yes. The energy raises the speed of the particles, but the thermometer is too slow to show it.
  3. Yes. The energy overcomes the attractions between particles instead of raising their speed.
Show the answer

Yes. The energy overcomes the attractions between particles instead of raising their speed.

During melting, energy is absorbed to break up the fixed arrangement, not to raise the average kinetic energy. A constant temperature does not mean no energy is transferred.

Cooling reverses these changes. As a gas condenses or a liquid freezes, attractions form between the particles and energy is given out. This energy balances the heat lost to the surroundings, so the temperature again stays constant. In every change of state, the particles stay the same size; only their arrangement, spacing and movement change.

Watch out for this

A student says: "Bromine melts at -7 degrees C and boils at 59 degrees C. At 25 degrees C it is a liquid, because 25 degrees C is above its melting point." What is wrong with this?

Show the answer

Being above the melting point only shows that bromine is not a solid. It is a liquid because 25 degrees C is above its melting point and below its boiling point. Above 59 degrees C it would be a gas. Examiners report many answers that compare the temperature with only the melting point or only the boiling point. Compare it with both.

Exam-style question

A pure liquid, X, is left to cool. Use its temperature readings to answer (a) to (d). [6]

Temperature of X as it cools
time / mintemperature / °C
090
274
463
663
863
1055
  1. (a) State the freezing point of X. [1]
  2. (b) State the physical state or states of X at 6 minutes. [1]
  3. (c) Explain, in terms of particles and energy, why the temperature stays constant from 4 to 8 minutes. [2]
  4. (d) Describe how the arrangement and movement of the particles change as X turns from liquid to solid. [2]

Saved on this browser only. Anyone using this browser can see it.